CTRL Assign1 (Controller Assign 1)

Use Knobs [C], [1] and [2] to assign Control Change Numbers to the Breath Controller, Knob [1] and Knob [2], respectively. The selected Control Change Name is shown on the left of the display.

 

 

 

 

 

 

 

 

 

 

 

CTRL

Assign1)

 

BC

Knob1

Knob2

￿

 

Vce

[FootCtrl]

 

02

16

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Control

 

Control

 

 

 

 

Change Name

 

Change Number

■BC (Breath Controller)

Specify a Control Change Number for this Assignable Controller. When MIDI information for this Assignable Controller is received, the specified Control Change is applied.

❏Settings: 00 ~ 95 (see the separate Data List for details)

■Knob1/2 (Knob [1]/[2])

Assign Control Change Numbers to Knobs [1] and [2] on the front panel.

❏Settings: 00 ~ 95 (see the separate Data List for details)

CTRL Assign2 (Controller Assign 2)

Use Knobs [C] and [1] to assign Control Change Numbers to the Foot Controller and Ribbon Controller, respectively. The selected function is shown on the left of the display. Use Knob [2] to select the Ribbon Controller Mode.

 

 

 

 

 

 

 

 

 

 

 

 

CTRL

Assign2)

 

FC

 

RB￿

 

 

Vce

 

[--------]

 

04

22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Control Change Name

Control Change

 

 

 

 

 

 

 

Number

■FC (Foot Controller)

Assign a Control Change Number to the Foot Controller. The Foot Controller is connected to the FOOT CONTROLLER connector on the rear panel (Page 13).

❏Settings: 00 ~ 95 (see the separate Data List for details)

■RB (Ribbon Controller)

Specify a Control Change Number for this Assignable Controller. When MIDI information for this Assignable Controller is received, the specified Control Change is applied.

❏Settings: 00 ~ 95 (see the separate Data List for details)

Details about Controller Assign settings in Performance Mode are given on Page 111.

PLG (Plug-in) (if a Plug-in Board has been installed)

If you have a Plug-in Board installed, the following two screens are available for setting its parameters. However, the number of sub-screens and parameters will vary depending on the type of Plug-in Board installed.

PLG MIDI (Plug-in MIDI)

PLG System (Plug-in System)

PLG MIDI (Plug-in MIDI)

Set the MIDI parameters of the Plug-in Board.

 

 

 

 

 

 

PLG MIDI)

Clock

DevNo

￿

 

PLG150-AN

on

all

 

 

 

 

 

 

■Clock

Select whether or not to transmit MIDI Clock messages to the Plug-in Board.

❏Settings: off, on

■DevNo (Device Number)

Set the MIDI Device Number of the Plug-in Board. This number must match the Device Number of the external MIDI device when transmitting/receiving bulk data, parameter changes or other system exclusive messages to/from it.

❏Settings: 1 ~ 16, all, off

PLG System (Plug-in System)

Set the system parameters for each Plug-in Board. Use Knob [C]/[2] to change the parameter. The number of screens and parameters will vary depending on the type of Plug-in Board installed. In the following example, a PLG150-AN Plug-in Board has been installed in the Plug-in slot.

 

 

 

 

 

PLG System) Vel Curve

Mrph CtrlNo￿

 

 

norm

off

 

 

 

 

 

Part Assign (assignment) for a Single-Part Plug-in Board is fixed as follows:

•Voice Mode: 1

•Performance Mode: 15

Utility Mode

133