Specifications 55
01V96i—Owner’s Manual
Specifications
Specifications

General Spec

Number of scene memories 99
Sampling Frequency
Internal 44.1kHz, 48 kHz, 88.2 kHz, 96 kHz
External
USB audio Normal Rate 44.1kHz ±0.1%
48kHz ±0.1 %
Double Rate 88.2 kHz ±0.1%
96kHz ±0.1 %
The others Normal rate: 44.1 kHz-10% to 48 kHz+6%
Double rate: 88.2 kHz-10% to 96 kHz+6%
Signal Delay fs=48 kHz Less than 1.6 ms CH INPUT to STEREO OUT
fs=96 kHz Less than 0.8 ms CH INPUT to STEREO OUT
Fader 100mm motorized 17
Fader Resolution +10 to –138, –dB input faders
0 to –138, –dB master faders, stereo fader
Total Harmonic Distortion1
(CH INPUT to STEREO OUT)
(Input Gain=Min.)
fs=48kHz Less than 0.05% 20 Hz–20 kHz @ +14dB i nto 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
fs=96kHz Less than 0.05% 20 Hz–40 kHz @ +14dB i nto 600 Ω
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
Frequency Response
(CH INPUT to STEREO OUT)
fs=48kHz 20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=96kHz 20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
Dynamic Range
(maximum level to noise level)
110 dB typ. DA Converter (STEREO OUT)
105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz
105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz
Hum & Noise2
(20 Hz–20 kHz)
Rs=150 Ω
–128dB Equivalent Input Noise
–86dB residual output noise. STEREO OUT (S TEREO OUT off)
Input Gain=Max.
Input Pad=0 dB
–86dB (90dB S/N) STEREO OUT
(STEREO fader at nominal level and all CH INPUT faders at minimum level)
Input Pad=0 dB
Input Sensitivity
=–60 dB
–64dB (68dB S/N) STEREO OUT
(STEREO fader at nominal level and one CH INPUT fader at nominal level)
Maximum Voltage Gain
74dB CH INPUT (CH1–12) to STEREO OUT/OMNI (BUS) OUT
40dB CH INPUT (CH13–16) to STEREO OUT
74dB CH INPUT (CH1–12) to OMNI (AUX) OUT (via pre input fader)
74dB CH INPUT (CH1–12) to MONITOR OUT (via STEREO BUS)
Crosstalk
(@ 1 kHz)
Input Gain=Min.
80dB adjacent input channels (CH1–12)
80dB adjacent input channels (CH13–16)
80dB input to output
AD Input (1–12)
Phantom switch +48 V DC (each 4ch)
Pad switch 0/20dB attenuation
Gain control 44dB (–60 to –1 6), detented
Peak indicator LED (red) turns on when post HA level reaches 3dB below clipping at dig-
ital domain
Signal indicator LED (green) turns on when post HA level reaches 20dB below nominal at
digital domain
AD converter 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
sampling (fs=88.2, 96 kHz)