Yamaha YDP-223 3. , 4. , 5. , 6.

YDP-223 Keyboard Stand Assembly

ENGLISH

54

3. Mount the main unit.

CAUTION

• Fingers can become pinched between the main

unit and the rear or side panels, be extra careful

so as not to drop the main unit.

• Do not hold the keyboard in any position other

than the position shown in the illustration.

4. Fix the main unit.

5. Connect the pedal cord.

6. Set the voltage selector and connect the

power cord.

Voltage Selector

Before connecting the AC power cord, check the setting

of the voltage selector which is provided in some areas.

To set the selector for 110V, 127V, 220V or 240V main

voltages, use a “minus” screwdriver to rotate the selector

dial so that the correct voltage for your region appears

next to the pointer on the panel. The voltage selector is

set at 240V when the unit is initially shipped. After the

proper voltage has been selected, connect the AC power

cord to the AC INLET and an AC wall outlet. A plug

adaptor may be also provided in some areas to match the

pin conﬁguration of the AC wall outlets in your area.

WARNING

An improper voltage setting can cause serious

damage to the YDP-223 or result in improper

operation.

R

Be sure to place your hands at least 10 cm

from either end of the main unit when positioning it.

At least

10 cm

(1) Center the main unit to pro-

duce equal clearance on

the left and right sides.

(2) Use 6x16 mm short screws

2 to secure the main unit

from the front.

PEDAL

(1) Insert the pedal cord plug to the

pedal connector from the front.

(3) Use a vinyl tie

to take up any

slack in the

pedal cord.

(2) Attach the cord holders to

the rear panel as shown,

then clip the cord into the

holders.

PC-1PC-2

Mac

MIDI

240

127

110

220

Contents

Main YDP-223 Digital piano Owner's Manual Bedienungsanleitung Mode d'emploi Manual de instrucciones IMPORTANT WICHTIG IMPORTANT SPECIAL MESSAGE SECTION CAUTION About this Owners Manual Trademarks: Table of Contents Appendix Reference Introduction Application Index PRECAUTIONS PRECAUTIONS Location Assembly Do not open * Please keep this manual in a safe place for future reference. Backing up the external media Saving and backing up your data Connections Saving data Accessories Maintenance Features [METRONOME] The YDP-223 includes 50 preset songs. TEMPO [] [] Before Using the YDP-223 Key C over To open the key cover: To close the key cover: Tur ning the Power On Setting the Volume Using Headphones Using the Headphone Hanger Using the Speaker Switch Reference YDP-223 Part Names Part Names Top panel VOICE REVERBEFFECT TOUCH TRANSPOSE 1 / L M N D E F G H I Connectors Tempo (Normal indication) A song number of 50 Greats for the Piano Listening to the Demonstration Tunes Demonstration tunes are provided that effectively demonstrate each of the YDP-223s voices. 1. 2. Press the [DEMO] button to engage Demo mode. The voice button indicators will ash in sequence. Listening to 50 Piano Preset Songs -1 223 To play back another song continuously, see procedure 2 above. 1. Press the [PRESET] button to engage Preset Song mode. The [PRESET], 4. Practicing a One-Hand Part Using 50 Preset Songs (Part Cancel Function) 1. 2. Press the SONG [START/STOP] button to start playback. Play the part you just turned off. 3. button once. Press the 1. 2. Specify the beginning (A) and the end (B) of the phrase, and start practicing. Damper (Right) Pedal Using the Pedals [MASTER VOLUME] Adding Variations to the Sound [BRILLIANCE]/ [REVERB]/[EFFECT] [REVERB] [BRILLIANCE] [EFFECT] Touch Sensitivity [TOUCH] [/NO] [+/YES] Transposition [TRANSPOSE] transposition Use the [/NO] and [+/YES] button while holding the [TRANSPOSE] button to transpose down or up as required. [/NO] [+/YES] 1. 2. Voice numbering priority 12 3456 7 1. TION# , ] buttons [TEMPO] indicator is lit). 2. [TEMPO/FUNCTION# ][/NO] [+/YES] The beat indicator flashes at the current tempo. Recording Your Performance Recording to [TRACK1] 1. 2. 3. 4. 5. 6. Re-recording TRACK1 Recording to [TRACK2] This section explains how to record another part on the second track. Changing the Initial Settings (Data recorded at the beginning of a song) YDP-223 Playing Back Recorded Songs Playing Back Recorded Songs [START/STOP] button. Playing Back a Song 1. 2. Useful Playback Functions Detailed Settings [FUNCTION] Basic Procedure in Function Mode FUNCTION / TEMPO 1. 2. Use the [TEMPO/FUNCTION# , ] buttons to select the desired function from F1F8. 3. 4. 5. tion. To exit Function mode, press the [TEMPO/FUNCTION#] button so that its About Each Function F1. Fine Tuning of the Pitch F2. Selecting a Scale Sub-mode F3.1: Dual Balance F3.2: Dual Detune F3.3: Voice 1 Octave Shift F3.4: Voice 2 Octave Shift F3.5: Voice 1 Effect Depth F3.6: Voice 2 Effect Depth F3. Dual Mode Functions F4. Other Functions F5 Metronome Volume F6. Preset Song Part Cancel Volume Sub-mode MIDI Transmit Channel Selection MIDI Receive Channel Selection Local Control ON/OFF F7. MIDI Functions Control Change ON/OFF Procedure F8. Backup Functions YDP-223 About MIDI About MIDI Use this connector to connect the YDP-223 to a computer. MIDI cables Prepare dedicated MIDI cables. [TO HOST] connector Connections Connectors 1 1234 56 YDP-223 Stereo 2 3 4 5 6 Connecting a Personal Computer 1. Connecting the serial port on the computer to the YDP-223s TO HOST jack mini DIN 8-pin D-sub 25-pin Windows Windows Macintosh TO HOST HOST SELECT Depending on the type of computer you connect, use one of the following serial cables. 2. Using a MIDI interface and the YDP-223s MIDI connectors Connection HOST SELECT POWER VOICE REVERBEFFECTTOUCHTRANSPOSE An example of connecting the USB interface to the YDP-223 using MIDI cables PC-1 Mac USB cable or Standard Machintosh 8-pin system peripheral cable MASTER VOLUME BRILLIANCE DEMOMETRONOMETEMPO Troubleshooting TIP Options & Expander Modules Problem Possible Cause and Solution YDP-223 Keyboard Stand Assembly Keyboard Stand Assembly 2. Remove the following parts from the package. 1. Attach the side panels to the pedal box. Have a Phillips-head (+) screwdriver ready. Assembly Parts 3. 4. 5. 6. Voltage Selector 7. After completing the assembly, please check the following. YDP-223 Preset Voice List Preset Voice List CHURCH ORGAN 2 CHURCH ORGAN 1 Demo Song List Stereo Index Numerics A B C R S T U V Page Function Function Default Backup Group YDP-223 Appendix/Anhang/Annexe/Apndice 61 MIDI Data Format / MIDI-Datenformat / Format des donnes MIDI / Formato de datos MIDI 1. NOTE ON/OFF Data format: [9nH] -> [kk] -> [vv] Data format: [8nH] -> [kk] -> [vv] (reception only) 2. CONTROL CHANGE 4. PROGRAM CHANGE Data format: [CnH] -> [ppH] 5. SYSTEM REALTIME MESSAGES 6. SYSTEM EXCLUSIVE MESSAGES (Yamaha MIDI Format) Panel Data Transmit Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... -> [F7H] YDP-223 Appendix/Anhang/Annexe/Apndice 63 General MIDI Mode On Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] -> [F7H] ll Data format: 10. Effect MIDI Map MIDI Implementation Chart Specications / Technische Daten / Caractristiques techniques / Especicaciones Page Page IMPORTANT SAFETY INSTRUCTIONS WARNING 1. 2. PLEASE KEEP THIS MANUAL FCC INFORMATION (U.S.A.) CAUTION: ATTENTION: CANADA U.S.A. NORTH AMERICA CENTRAL & SOUTH AMERICA EUROPE AFRICA MIDDLE EAST ASIA