Speaker angle and Non skid pad
You can adjust the speaker angle. Loosen the screw on the bottom of the speaker stand as shown in the figure, adjust the angle of the stand, and tighten the screw to fix the stand.
To prevent the speakers from sliding around, attach the supplied pads to the four points on the bottom of each satellite speaker. Place the speaker on a stable, flat surface.
Specifications
Loosen | Tighten |
|
* |
| Speaker stand |
|
| |
| * | * Non skid |
|
| pad |
English
Type .................................. | Advanced Yamaha Active |
| Servo Technology |
Output power |
|
Satellite.............................. | 6 W + 6 W (1 kHz, 4Ω at |
| T.H.D.=10%) |
Subwoofer ......................... | 18 W (100 Hz, 4Ω at |
| T.H.D.=10%) |
Input sensitivity.............. | 200 mV (1 kHz, 4Ω at 6 W) |
Input impedance ............ | 20 kΩ |
Frequency response ....... | 45 Hz to 20 kHz (Satellite + |
| Subwoofer) |
Crossover Frequency....... | Satellite/Subwoofer 180 Hz |
Driver
Satellite.................... | 5 cm (2") cone, magnetic shielding | |
Subwoofer ............... | 12 cm (5") cone, magnetic shielding | |
Power supply (AC adapter) | ||
U.S.A. and Canada models | .........AC 120 V, 60 Hz | |
Australia model ........................... | AC 240 V, 50 Hz | |
U.K. and Europe models ............. | AC 230 V, 50 Hz | |
Dimensions (W ⋅ H ⋅ D) |
| |
Satellite speakers ............... | 65 (2.6") ⋅ 75 (3") ⋅ 119 | |
|
| (4.7") mm |
Subwoofer ......................... | 183 (7.2") ⋅ 196 (7.7") ⋅ 183 | |
(7.2") mm
Input Section
Subwoofer ......................... | 3.5 mm stereo mini jack for |
| |
Output Section |
|
Subwoofer ......................... | RCA pin jack connected to |
| left satellite speaker |
| 8 pin jack connected to right |
| satellite speaker |
Weight
Satellite speakers ............... | Right: 0.45 kg (1 lb.) |
| Left: 0.36 kg (13 oz.) |
Subwoofer ......................... | 2.3 kg (5 lbs. 1 oz.) |
Accessories
AC adapter ⋅ 1
3.5mm stereo mini plug cable ⋅ 1 (1.8 m) 8 pcs of non skid pads ⋅ 1 set
* Specifications subject to change without notice.
Troubleshooting
If the speakers fail to operate normally, check the following table. It lists common operation errors and simple measures that you can take to correct problems. If a problem cannot be corrected, or the symptom is not listed, disconnect the AC adapter and contact your authorized YAMAHA dealer or service center for help.
FAULT |
|
|
| CAUSE |
|
|
| CURE |
|
|
|
|
|
|
|
|
|
|
|
No sound comes | The AC adapter is not properly plugged into | Insert the AC adapter firmly into the AC recepta- |
| ||||||
from the speakers | the AC receptacle. | cle. |
| ||||||
or subwoofer. | The |
|
| (standby/on) button is turned off. | Turn on the |
|
| (standby/on) button (the indicator |
|
|
|
|
|
| |||||
|
|
|
|
|
| ||||
|
|
|
|
| lights). |
| |||
| Connections are faulty or incomplete. | Make the connections again, firmly, or use a differ | - | ||||||
|
|
|
|
| ent cable. |
| |||
| The volume is set to minimum. | Turn the speaker VOLUME control to the right to |
| ||||||
|
|
|
|
| increase the volume. |
| |||
| The level of the signal being input is too low. | Turn up the volume on the connected component. |
| ||||||
|
|
|
|
|
|
|
|
|
|
The bass sound can | The BASS control is set to minimum. | Turn the subwoofer BASS control to the right to |
| ||||||
not be heard. |
|
|
|
| increase the volume. |
| |||
|
|
|
|
|
|
|
|
|
|
Sound is distorted. | The level of the signal being input is too high. | Turn down the volume on the connected component. |
| ||||||
|
|
|
|
|
|
|
|
|
|
Noise. | Connections are faulty or incomplete. | Make the connections again, firmly, or use a differ | - | ||||||
|
|
|
|
| ent cable. |
| |||
|
|
|
|
|
|
|
|
|
|
3