HP e1200-160 manuals
Computer Equipment > Network Router
When we buy new device such as HP e1200-160 we often through away most of the documentation but the warranty.
Very often issues with HP e1200-160 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Network Router HP e1200-160 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Network Router on our side using links below.
200 pages 3.96 Mb
2 Network Storage Router e1200-16010 Intended AudiencePrerequisites Related Documentation 11 Conventions consist of the following:■Document Conventions ■Text Symbols ■Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases 12 Text SymbolsEquipment Symbols WARNING: 13 Rack stability protects personnel and equipment■The leveling jacks are extended to the floor ■The full weight of the rack rests on the leveling jacks ■In single rack installations, the stabilizing feet are attached to the rack ■In multiple rack installations, the racks are coupled 14 HP Technical SupportHP Storage Website 15 HP Authorized Reseller17 Introduction125 Configuration Overview35 Visual Manager UserInterface37 Main MenuFigure 6: Visual Manager Main menu tree 38 Visual Manager (VM) can be accessed from any standard Web browser:1.Connect a 10/100BaseT Ethernet cable to the back of the router 2.Apply power to the connected SCSI and/or Fibre Channel devices 3.Apply power to the host computer The factory default for the IP address is http://1.1.1.1 http://1.1.1.1 5.Select the desired menu option to access menus and screens 39 Enter the authorized user name and password. The username and password areThe default user name is root and the default password is password Figure 7: Password Dialog Box Note: HP recommends changing the user name and password from the defaults 40 SubmitConfigure 43 HomeSystem Ports Discovery Mapping Statistics Utilities Report Reboot 44 SerialNetwork SNMP Active Fabric User 45 Real-TimeClock ■Reset Menu 47 Network Settings48 Port Configuration - Ethernet Settings (Service Mode - Restricted Access)See Figure 14 for an example of the Ethernet Configuration dialog box Figure 14: Ethernet Configuration dialog box Ethernet configuration settings: ■Ethernet Mode can be set to one of the following options: —10Mps Only —100Mps (half duplex) Only —100Mps (full duplex) Only —10/100Mps (Auto-Neg.) ■MAC address is the Ethernet physical address of the router 49 The Ethernet physical address is always assigned by the manufacturer■IP address (default: 1.1.1.1) is the IP address of the router ■Subnet Mask (default: 255.255.255.0) is the IP subnet mask for the router IP Gateway DHCP SNMP Configuration SNMP configuration is not supported 50 Number of Controller LUNs51 User ConfigurationUser Name Password 52 Real-TimeClock ConfigurationDate Settings Day of Week Time Settings 53 Reset MenuThe Reset Menu is used to reset the router to factory default settings Figure 18 is an example of the Reset Menu Figure 18: Reset to Factory Default screen 55 SubmitPorts Menu tasks: ■Fibre Channel Port configuration changes Fibre Channel port settings ■SCSI Bus configuration changes SCSI bus settings Each Ports Menu option is discussed in the following subsections 56 Link StatusPort Name High 57 Port Name Low■Port Mode (default: N_Port) sets the port mode Port Mode settings: Auto Sense: N_Port: Use Hard AL_PA enables or disables Hard AL_PA usage Hard AL_PA Settings displays the AL_PA Lookup Table Discovery Mode Discovery mode settings: Auto Discovery on Reboot Events Auto Discovery on Link Up Events Both the ports and the devices behind the ports are discovered for the first 58 Manual Discovery OnlyBuffered Tape Writes Buffered Tape Queue Depth Default Map The current map can be set to: —Auto-assignedcontains all the SCSI devices that are attached to the router —SCC 59 ■Performance Mode (default: 2 Gb/s) toggles between 1 Gb/s and 2 Gb/sOverride Settings —Hi-SupBit toggles between Set and Clear Force FCP Response Code Off —Initiator Bit toggles between Set and Clear toggles between and —Link Garbage Deletion toggles between Enabled and Disabled 60 Primary Initiator IDAlternate Initiator ID Target ID(s) 61 Note: Target IDs must be setup before mapping devices on the SCSI bus■Discovery toggles between Enabled and Disabled Discovery Delay ■Bus Reset on Boot toggles between Enabled and Disabled ■Internal Termination toggles between Enabled and Disabled ■Buffered Tape Writes (default: Enabled) toggles between Enabled and Disabled 62 —Auto-assigned(default) contains all the devices attached to the router—Indexed —Custom SCSI bus override settings: —CDB Length Override enables or disables the override of default CDB lengths —CDB Group 6 Length Default (default: 0) can be set to 0, 6, 10, or —CDB Group 7 Length Default (default: 0) can be set to 0, 6, 10, or —Wide Negotiation enables or disables negotiation on a wide SCSI bus Synchronous Negotiation 63 Synchronous Parameter OverrideSynchronous Period Synchronous Offset Ultra SCSI-3 Negotiation 65 Each physical port/bus on the router can have the following maps:To view or change map settings of a specific port or bus: To make changes to the configuration, enter the new value and then select ■Common Fibre Channel and SCSI Mapping Tasks, page ■Fibre Channel Mapping Tasks, page ■SCSI Mapping Tasks, page 66 Common Fibre Channel and SCSI Mapping TasksSelect Host Edit/View Host Delete Host 67 ■Add Map adds a new mapAdd ■Select Map adds a known map ■Edit/View Map displays or changes map information Viewing and changing map information is discussed in the following paragraphs ■Delete Map deletes the current map Fibre Channel Mapping Tasks Configuration tasks for Fibre Channel mapping includes: ■Viewing and Changing Fibre Channel Host Information, page Viewing and Changing Fibre Channel Map Information Each task is discussed in the following paragraphs 68 Viewing and Changing Fibre Channel Host Information69 Viewing and Changing Fibre Channel Map Information70 Discovered Device EntryCreate Entry Manual Device Entry 71 Viewing and Changing SCSI Host Information72 Viewing and Changing SCSI Map Information73 SCSI Map settings:74 Reset SCSI system statistics75 FTP Utility access■Trace Settings configuration configures trace settings Current Traces display Previous Traces display Last Assert Traces display Clear Current Traces Clear Assert Traces 76 Event Log SettingsEvent Log display Clear Event Log 77 FTP Utility AccessThe FTP utility screen is used to open an FTP session Figure 28 is an example of the FTP utility screen 78 To open an FTP session:1.Enter the User Name, Password, and the IP address of the router 2.Click Connect Select the local file to upload or download. If necessary, click Browse The following file types can be uploaded to the router: ■Configuration (.cfg) ■Firmware (.dlx) The following file types can be downloaded from the router: ■Traces for the current boot cycle (curtrace.txt) ■Traces from the previous boot cycle (prvtrace.txt) 4.Click Binary Transfer mode 5.Choose the desired task: ■To download a file, click Get ■To upload a file, click Put 79 Trace Settings Configuration80 Table 6 is a brief description list of the trace settings81 Current, Previous, and Last Assert Trace Displays82 Clear Current Traces and Clear Assert Traces83 Event Log ConfigurationEvent Log settings: ■Log All Events ■Disable/Enable Event Logging ■Log Error Events ■Log Notify Events Event logging captures the last 215 events and then starts overwriting the log 84 Event Log Display85 Clear Event Log 89 Serial/Telnet User Interface92 1.From the Windows Start Menu, open the Command Prompt (DOS) window2.At the ‘>’ prompt, enter: where <IP ADDRESS> is the IP address of the router 3.Enter the user name and password To open a serial session, a terminal emulator utility is required From most Windows 9x, Windows NT, and Windows 2000 systems, a HyperTerminal session can be started using the following steps: 1.From the Windows Start Menu, open HyperTerminal 2.Name the new terminal session 3.Indicate the appropriate COM port 93 Enter94 Power up Messages95 ■1) Perform Configuration enters router configuration settings■2) System Utilities displays system statistics and perform diagnostic tests 3) Display Trace and Assertion History displays trace information and clear the trace buffer ■4) Reboot reboots the router 5) Download a New Revision of the Firmware Each Main Menu option is discussed in a separate section of this chapter 96 The Configuration Menu is used to configure the routerFigure 39 is an illustration of the Configuration Menu Figure 39: Configuration menu Configuration Menu options: ■1) Baud Rate Configuration changes the baud rate on the serial port 2) Ethernet enters Ethernet network settings 3) Fibre Channel Configuration ■4) Parallel SCSI Configuration configures the settings for the SCSI buses 97 5) Device Mapping6) Trace and Event Settings Configuration ■7) Real-TimeClock Configuration sets the system clock 8) Active Fabric Configuration A) Save Configuration B) Restore Last Saved Configuration C) Reset and Save Configuration to Factory Defaults X) Return to Main Menu Baud Rate Configuration 1) Baud Rate configuration 98 Ethernet Configurationand SNMP (SNMP not supported) 99 To view or change configuration settings:1.Select a menu option 2.Make the configuration changes 3.Select X) Return to previous menu to record the changes. Ethernet Configuration Menu options: ■1) Change IP address (default: 1.1.1.1) changes the router IP address 2) Change IP Subnet Mask 3) Change IP Gateway 4) Change Ethernet Physical Address changes the Ethernet physical address (MAC address) ■5) Toggle Ethernet Mode changes the Ethernet mode. Options include: changes the Ethernet mode. Options include: —10 Mb/s only —100 Mb/s (half duplex) only —100 Mb/s (full duplex) only —10/100 MPS (Auto-Neg.) ■6) Change Hostname changes the name of the host server 100 7) Toggle DHCP Configuration■8) Change SNMP Settings is not supported is not supported 9) Change Security Settings 101 Fibre Channel Configuration102 Fibre Channel Configuration Menu options:Change World Wide Name High (service mode-restricted access) changes the World Wide Port Name High Change World Wide Name Low access) changes the World Wide Port Name Low 3)Toggle Hard AL_PA Usage changes the Hard AL_PA usage to either Yes or No If set to Change AL_PA Value Toggle Discovery Mode Auto Discovery on Link-up Events 103 6) Toggle Buffered Tape Writes7) Change Buffered Tape Queue Depth changes the tape backup queue depth. Select a value from 0 through 8) Toggle Port Mode Auto Sense N_Port 9) Change Default Map Value Mapping modes can be Auto-Assigned,Indexed (default), or SCC A) Edit FC Override Settings 104 1) Toggle2) Toggle Forcing FCP Response Code 3) Toggle Initiator Bit Setting in PRLI_ACC 4) Toggle FC Link Garbage Deletion 105 Parallel SCSI ConfigurationFigure 43 is an illustration of the Parallel SCSI Configuration Menu Current settings for the selected SCSI bus are displayed 106 SCSI Configuration Menu options:1) Edit Initiator and Target Settings changes the SCSI Initiator and Target settings 1) Enable/Disable SCSI Initiator enables or disables the SCSI Initiator. Options are 2) Select primary and select/enable alternate SCSI ID These should be unique IDs on the bus —3) Add Target ID or —4) Remove Target ID adds or removes a Target ID Note: Target IDs must be setup prior to mapping devices on the SCSI bus ■2) Enable/Disable SCSI Discovery enables or disables the Discovery Mode 3) Enable/Disable SCSI Reset on Boot enables or disables automatic bus resets after a reboot 4) Set Discovery Delay Time 107 ■5) Set SCSI Termination Mode enables or disables the SCSI termination modeenables or disables the SCSI termination mode 6) Edit SCSI Target Override Settings —1) Toggle CDB Length Override: enabled or disabled : enabled or disabled If enabled, the following configuration options are displayed: CDB Group 6 Length Default CDB Group 7 Length Default —2) Toggle Wide Negotiation: enabled or disabled —3) Toggle Synchronous Negotiation: enabled or disabled —4) Toggle Synchronous Parameter Override: enabled or disabled Enable/Disable Buffered Tape Writes (default: Enabled) enables or disables Buffered Tape Writes Change Default Map Value X)Return to previous menu returns to previous menu Command <Enter> scrolls to the next SCSI bus 108 Device Mapping109 Selecting the Current Map110 Displaying the Current Map111 Editing the Current Map112 Map Edit Menu options:■1) Edit Name changes the name of the current map ■2) Edit Map Entries changes the content of the current map ■3) Clear Map erases all entries from the current map 4) Fill Map 113 Next (N)Previous (P) Add (A) 114 Create (C)Remove Gaps (R) Delete (D) Exit (X) 115 To add a new entry to a SCSI map:1.In the Edit Map Entries screen, select Add (A) 2.Enter a Target/LUN ID combination To pre-entera map entry for devices that are not yet online, select Create (C) 117 Remove (R)118 Editing the Host List for the Current Map119 Edit (E)121 If the host is a SCSI host, the host name and the initiator ID must be enteredTo change host information, select Edit (E) Enter 123 Displaying the Entire Device List124 Figure 59 is an illustration of the Entire Device screenFigure 59: Entire Device List screen Trace and Event Settings Configuration 5) Trace and Event Settings Configuration Figure 60: Utility Settings (trace settings) menu 125 Configuring Trace Settings126 Configuring Event Settings127 Settings include:■1) Log All Events (default) (default) ■2) Disable Event Logging ■3) Error Events ■4) Notify Events U) Update Current Operating Trace levels Real-time Clock Configuration Figure 64 is an illustration of the System Clock Setup Menu 1.To change the date or time, select 1) Set Clock 2.A series of prompts are displayed, allowing setup of: ■24-hourtime ■Current date ■Current day of the week 128 Save Configuration129 Restore Last Saved ConfigurationReset and Save Configuration to Factory Defaults C) Reset and Save Configuration 130 System Utilities MenuFigure 66 is an illustration of the System Utility Menu System Utility Menu options: ■1) System Statistics Menu displays a variety of system status information ■2) Event Log displays the system Event Log 3) Enter System Diagnostics Mode performs Ethernet, SCSI, and Fibre Channel connection tests 4) Special Fibre Channel Link States 131 Viewing System Status Information132 Viewing Fibre Channel Status Information133 2) Display Attached Fibre Channel Devices3) Display Fibre Channel Resource Status 4) Display Fibre Channel Driver Resource Status Display Fibre Channel Link Status Autorepeat 135 To view a list of the devices attached to this port:In the Fibre Channel Status Menu, choose The Fibre Channel Device Display page is displayed 2. To refresh the display, select R) Refresh Device Display 3. To view device details, select D) Display Device Details 136 To view FCP transport information, in the Fibre Channel Status Menu, chooseDisplay Fibre Channel Resource Status Figure 72 is an illustration of the FCP Transport Queue page The Fibre Channel Driver Queues page is displayed 137 Viewing SCSI Status Information138 1) Issue discovery for all buses2) Issue discovery for selected bus 3) Issue boot discovery 4) Display all local devices 5) Display local devices on specified bus 139 Event Log1) Display event log 2) Clear event log 140 1) Display trace for current boot cycle2) Display trace from previous boot cycle 3) Display trace from the last assertion failure 4) Clear current trace buffer 5) Clear (flash) assert trace buffer Saving Copies of the Trace Buffers using FTP 141 5.Enter the user name and passwordThe factory default user name is root and the default password is password 6.Specify Bin mode: 7. Enter the appropriate command to copy the current or previous trace buffer: ■To copy the current trace buffer: ■The file will transfer from the router ■To copy the previous trace buffer: 142 1.Select 5) Download a New Revision of the Firmware in the router Main MenuTransfer, Send File Send 145 FTP User Interface151 Basic Troubleshooting163 Serial and Ethernet Pin Assignments167 Controller LUN Commands173 Addressing Methods and Table Structures179 Regulatory Compliance Notices187 Electrostatic Discharge188 ■Use a wrist strap connected by a ground cord to a grounded workstation orcomputer chassis. Wrist straps are flexible straps with a minimum of ■Use conductive field service tools ■Use a portable field service kit with a folding static-dissipatingwork mat 189 audienceauthorized reseller, HP 15 auto-assignedaddressing described 176 auto-assignedmaps, defined Serial/Telnet UI 97 Visual Manager UI buffered tape writes Fibre Channel Serial/Telnet UI Visual Manager UI 58 overview of Visual Manager UI 61 bus reset on boot overview of 29 Serial/Telnet UI 106 Visual Manager UI Center for Devices and Radiological Health See CDRH clock configuration Serial/Telnet UI 127 Visual Manager UI configuration settings backing up 147 common 29 restoring 148 troubleshooting configurations, Fibre Channel to SCSI, illustrated controller LUN commands general commands, listed conventions document 11 equipment symbols 12 text symbols conversion process, FCP to SCSI protocol, illustrated copying trace buffers, FTP UI 149 current map, default Fibre Channel Serial/Telnet UI 103 Visual Manager UI Visual Manager UI date configuration 193 deleting (removing) the current map Visual Manager UIdeleting a host from the host list Serial/Telnet UI 121 Visual Manager UI displaying the entire device list Serial/Telnet UI editing entries Serial/Telnet UI editing the host list of the current map Serial/Telnet UI overview of Visual Manager UI 65 selecting a host for the current map Visual Manager UI 67 viewing and changing Visual Manager UI 66 mapping tasks, SCSI adding entries Serial/Telnet UI 115 Visual Manager UI clearing entries Visual Manager UI 73 creating entries Visual Manager UI 73 default current map Visual Manager UI 62 deleting entries Visual Manager UI 73 filling entries Visual Manager UI 73 removing gaps in Visual Manager UI 73 viewing and changing 108 Visual Manager UI maps network configuration Serial/Telnet UI 98 Visual Manager UI override settings Fibre Channel Visual Manager UI 59 SCSI parts proper handling 187 storing performance mode, Fibre Channel Visual Manager UI pin assignments DB-9serial 164 RJ-45Ethernet pin layout DB-9serial 164 RJ-45Ethernet 194 port configuration Serial/Telnet UIpower requirements, of router 24 power supply power-upmessages, illustrated 94 prerequisites PRLI data, troubleshooting process, converting Fibre Channel to SCSI, illustrated process, converting SCSI to Fibre Channel, illustrated rack stability, warning 13 rebooting Canadian 182 European Union related documentation 10 report option RJ-45Ethernet pin layout, illustrated 165 router, illustrated 18 SCC addressing, described 176 SCC maps, defined SCSI bus buffered tape writes Serial/Telnet UI 107 Visual Manager UI bus reset on boot Serial/Telnet UI 106 Visual Manager UI configuration of Serial/Telnet UI 105 Visual Manager UI configuration overview 29 configuration, troubleshooting 155 default map Visual Manager UI 62 discovery settings LED indicators 19 override settings Visual Manager UI 62 termination mode Visual Manager UI 61 SCSI devices, troubleshooting 157 SCSI hosts SCSI maps adding entries Visual Manager UI 73 clearing entries 196 editing the host list of the current map, edit options, listedinitial access 108 listed screen navigation 109 selecting the current map selecting the host for the current map 120 viewing the current map overview of the UI 27 port configuration 101 reboot option, described Restore Last Saved Configuration option, described Save Configuration option, described 128 SCSI attached devices SCSI resource information 138 SCSI statistics SCSI status information described trace buffers, saving copies 140 Trace Dump menu, described trace settings, configuring 125 Serial/Telnet UI Active Fabric Configuration Menu, illustrated Serial/Telnet UI adding a host to the host list - FCP host, illustrated Serial/Telnet UI Baud Rate Configuration screen, illustrated Serial/Telnet UI Configuration Menu, illustrated Serial/Telnet UI creating an entry for a SCSI map, illustrated Serial/Telnet UI creating an map entry for a Fibre Channel map, illustrated Serial/Telnet UI device list generated for a Fibre Channel port, illustrated Serial/Telnet UI Device Mapping Configuration Menu, illustrated Serial/Telnet UI Download New Firmware Menu, illustrated Serial/Telnet UI Edit Map Entries for a Fibre Channel Map, illustrated Serial/Telnet UI Edit Map Entries for a SCSI Map, illustrated Serial/Telnet UI editing host information on a SCSI bus, illustrated illustrated Serial/Telnet UI Fibre Channel configuration screen, illustrated Serial/Telnet UI Fibre Channel Devices Display page, illustrated Serial/Telnet UI Fibre Channel Driver resource status screen, illustrated Serial/Telnet UI Fibre Channel link status screen, illustrated Serial/Telnet UI Fibre Channel Status Menu, illustrated 198 Serial/Telnet UI 142 user configurationSerial/Telnet UI 100 Visual Manager UI user interfaces, listed 27 utilities configuration Serial/Telnet UI 130 Visual Manager UI Visual Manager Clear Current Trace Buffer screen, illustrated Visual Manager Current traces screen, illustrated box, illustrated Visual Manager Event Log settings screen, illustrated Visual Manager SCSI Host Name dialog box, illustrated Visual Manager SCSI Map dialog box, illustrated illustrated 79 Visual Manager UI accessing Active Fabric configuration 50 number of controller LUNs 50 options baud rate configuration 46 best practices clock configuration 52 discovery Ethernet configuration 48 DHCP Ethernet mode 48 IP address IP gateway 49 subnet mask event log clearing 85 configuration 83 display factory settings, resetting 53 Fibre Channel link status 56 override settings 59 performance mode 59 port mode Fibre Channel hosts, viewing and changing FTP access 77 home page host name, changing 47 I/O configuration 54 main menu 41 mapping tasks overview of 65 mapping tasks, Fibre Channel adding entries 70 clearing maps 69 creating entries
Also you can find more HP manuals or manuals for other Computer Equipment.