Bryant 581J specifications

581J

23 81 19.13.J. Coils

1.Standard Aluminum Fin/Copper Tube Coils:

a.Standard evaporator and condenser coils shall have aluminum lanced plate fins mechanically bonded to seam- less internally grooved copper tubes with all joints brazed.

b.Evaporator coils shall be leak tested to 150 psig, pressure tested to 450 psig, and qualified to UL 1995 burst test at 1775 psig.

c.Condenser coils shall be leak tested to 150 psig, pressure tested to 650 psig, and qualified to UL 1995 burst test at 1980 psig.

2.Optional Pre-coated aluminum-fin condenser coils:

a.Shall have a durable epoxy-phenolic coating to provide protection in mildly corrosive coastal environments.

b.Coating shall be applied to the aluminum fin stock prior to the fin stamping process to create an inert barrier between the aluminum fin and copper tube.

c.Epoxy-phenolic barrier shall minimize galvanic action between dissimilar metals.

3.Optional Copper-fin evaporator and condenser coils:

a.Shall be constructed of copper fins mechanically bonded to copper tubes and copper tube sheets.

b.Galvanized steel tube sheets shall not be acceptable.

c.A polymer strip shall prevent coil assembly from contacting the sheet metal coil pan to minimize potential for galvanic corrosion between coil and pan.

4.Optional E-coated aluminum-fin evaporator and condenser coils:

a.Shall have a flexible epoxy polymer coating uniformly applied to all coil surface areas without material bridging between fins.

b.Coating process shall ensure complete coil encapsulation of tubes, fins and headers.

c.Color shall be high gloss black with gloss per ASTM D523-89.

d.Uniform dry film thickness from 0.8 to 1.2 mil on all surface areas including fin edges.

e.Superior hardness characteristics of 2H per ASTM D3363-92A and cross-hatch adhesion of 4B-5B per ASTM D3359-93.

f.Impact resistance shall be up to 160 in.-lb (ASTM D2794-93).

g.Humidity and water immersion resistance shall be up to minimum 1000 and 250 hours respectively (ASTM D2247-92 and ASTM D870-92).

h.Corrosion durability shall be confirmed through testing to be no less than 1000 hours salt spray per ASTM B117-90.

5.Optional E-coated aluminum-fin, aluminum tube condenser coils:

a.Shall have a flexible epoxy polymer coating uniformly applied to all coil external surface areas without mater- ial bridging between fins or louvers.

b.Coating process shall ensure complete coil encapsulation, including all exposed fin edges.

c.E-coat thickness of 0.8 to 1.2 mil with top coat having a uniform dry film thickness from 1.0 to 2.0 mil on all external coil surface areas, including fin edges, shall be provided.

d.Shall have superior hardness characteristics of 2H per ASTM D3363-00 and cross-hatch adhesion of 4B-5B per ASTM D3359-02.

e.Shall have superior impact resistance with no cracking, chipping or peeling per NSF/ANSI 51-2002 Method 10.2.

23 81 19.13.K. Refrigerant Components

1.Refrigerant circuit shall include the following control, safety, and maintenance features:

a.Thermostatic Expansion Valve (TXV) shall help provide optimum performance across the entire operating range. Shall contain removable power element to allow change out of power element and bulb without remov- ing the valve body.

b.Refrigerant filter drier - Solid core design.

c.Service gauge connections on suction and discharge lines.

d.Pressure gauge access through a specially designed access port in the top panel of the unit.

2.There shall be gauge line access port in the skin of the rooftop, covered by a black, removable plug.

a.The plug shall be easy to remove and replace.

b.When the plug is removed, the gauge access port shall enable maintenance personnel to route their pressure gauge lines.

c.This gauge access port shall facilitate correct and accurate condenser pressure readings by enabling the read- ing with the compressor access panel on.

62