Chapter 2 Installation Overview

Installation Guidelines

Installation Guidelines

Because the bridge is a radio device, it is susceptible to common causes of interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:

•Install the bridge in an area where structures, trees, or hills do not obstruct radio signals to and from the bridge.

•Install the bridge at a height sufficient to provide clear line-of-sight signal path.

Site Surveys

Every network application is a unique installation. Before installing multiple bridges, you should perform a site survey to determine the optimum use of networking components and to maximize range, coverage, and network performance.

Consider the following operating and environmental conditions when performing a site survey:

•Data rates—Sensitivity and range are inversely proportional to data bit rates. The maximum radio range is achieved at the lowest workable data rate. A decrease in receiver sensitivity occurs as the radio data increases.

•Antenna type and placement—Proper antenna configuration is a critical factor in maximizing radio range. As a general rule, range increases in proportion to antenna height. However, do not place the antenna higher than necessary, because the extra height also increases potential interference from other unlicensed radio systems.

•Physical environment—Clear or open areas provide better radio range than closed or filled areas.

•Obstructions—Physical obstructions such as buildings, trees, or hills can hinder performance of wireless devices. Avoid locating the devices in a location where there is an obstruction between the sending and receiving antennas.

Unpacking the Bridge

Note If you are unpacking an external antenna bridge, do not remove the foam block attached to the face of the bridge until the bridge is installed. The foam protects the antenna connector.

Follow these steps to unpack the bridge:

Step 1 Open the shipping container and carefully remove the contents.

Step 2 Return all packing materials to the shipping container and save it.

Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment. If any item is damaged or missing, notify your authorized Cisco sales representative.

Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03

 

OL-4072-04

2-5

 

 

 

Page 30 Page 32
Page 31
Image 31
Cisco Systems 1400 manual Installation Guidelines, Site Surveys, Unpacking the Bridge
Page 30 Page 32

1400 specifications

Cisco Systems 1400, known for its robust networking solutions, is a versatile and powerful device designed to enhance connectivity in various environments. The Cisco 1400 is part of the Cisco Industrial Router series and is tailored specifically for industrial applications, particularly in challenging environments where durability and reliability are paramount.

One of the main features of the Cisco 1400 is its rugged construction. It is built to withstand extreme temperatures, vibrations, and dust, making it ideal for deployment in factories, oil and gas rigs, and outdoor installations. This ruggedness ensures operational continuity in situations where standard networking equipment might fail.

Connectivity is another primary characteristic of the Cisco 1400. It supports a variety of WAN and LAN interfaces, including Serial, Ethernet, and cellular connections. This multifunctionality allows for flexible network design, enabling organizations to integrate the device into existing infrastructure seamlessly. Furthermore, it facilitates remote access, making it suitable for managing distributed networks in real-time.

The Cisco 1400 integrates advanced security features to safeguard data and network integrity. With support for VPN, firewall, and intrusion prevention systems, it provides a secure platform for critical communications. The device is also compliant with various industry standards and regulatory requirements, ensuring that organizations can maintain robust security postures in line with compliance mandates.

Another notable technology featured in the Cisco 1400 is its support for Cisco’s IoT capabilities. It can connect and manage numerous IoT devices, providing enhanced monitoring and data collection critical for industrial applications. This feature supports the concept of Industry 4.0, allowing businesses to leverage data analytics for predictive maintenance and operational efficiency.

Management and configuration of the Cisco 1400 are simplified through the use of Cisco Prime Infrastructure and Cisco DNA Center. These management tools provide intuitive dashboards and automated processes, streamlining network operations.

In summary, the Cisco Systems 1400 is a powerful, rugged networking solution designed for industrial applications. With its versatile connectivity options, robust security features, support for IoT technologies, and simplified management capabilities, it stands out as an exceptional choice for organizations looking to enhance their network infrastructure in challenging environments. This makes the Cisco 1400 an ideal solution for modern industrial connectivity needs.
Top Page Image Contents