Replace an OC-48 Card

OC48/STM16 LR/LH 16 Port 1550 Card OGI Connector Pinout

Table 5 shows the OC48/STM16 LR/LH card OGI connector pinouts.

Table 5

OC48/STM16 LR/LH 16 Port 1550 Card OGI Connector Pinout

 

 

 

 

 

 

 

 

 

 

 

 

 

Connector

 

OGI Pin and Card Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

Transmit 4

Receive 4

Transmit 3

Receive 3

Transmit 2

Receive 2

Transmit 1

Receive 1

 

 

 

 

 

 

 

 

 

 

2

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

Transmit 8

Receive 8

Transmit 7

Receive 7

Transmit 6

Receive 6

Transmit 5

Receive 5

 

 

 

 

 

 

 

 

 

 

3

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

Transmit 12

Receive 12

Transmit 11

Receive 11

Transmit 10

Receive 10

Transmit 9

Receive 9

 

 

 

 

 

 

 

 

 

 

4

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

Transmit 16

Receive 16

Transmit 15

Receive 15

Transmit 14

Receive 14

Transmit 13

Receive 13

 

 

 

 

 

 

 

 

 

 

Replace an OC-48 Card

Purpose

This procedure is used to replace a faulty OC-48 card.

Tools/Equipment

Replacement OC-48 card

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite

Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry could constitute an energy hazard.

Note Card removal raises an improper removal (IMPROPRMVL) alarm, but this clears after the card replacement is completed.

Step 1 Log into the node where you will replace the OC-48 card. If necessary, refer to the

Cisco ONS 15600 Procedure Guide for a login procedure.

Step 2 Ensure that the card you are replacing does not carry traffic in a 1+1 group:

a.In the node view, click the Maintenance > Protection tabs.

b.Choose the first group listed under Protection Groups.

c.Verify that the slot number for the card you are replacing does not appear in the Selected Groups list. For example, if you are replacing the OC-48 card in slot 3, make sure that Selected Groups does not contain any entries that start with s3, regardless of the port.

d.Repeat Steps b and c for each protection group.

e.If any of the groups contain a port on the card you want to replace, perform the “Force-Switch 1+1 Ports” task on page 10 .

Installing the Cisco ONS 15600 OC48/STM16 LR/LH 16 Port 1550 Card

8

78-15182-01

 

 

Page 8
Image 8
Cisco Systems ONS 15600 OC48/STM 16 Replace an OC-48 Card, OC48/STM16 LR/LH 16 Port 1550 Card OGI Connector Pinout