8.4.4, Controller, 8.4.5, Wiring, P/N 106-2477SP | Frymaster H17SC

Image 63

Frymaster H17SC, H22SC 8.4.4, Controller, 8.4.5, Contactor Box Wiring Assembly - 12-Pin Full-Vat C-1, P/N 106-2477SP

Contents

8196004 24-Hour Service HotlineandPartsManualService,Operation,Installation FRYERS DANGER CANADA Never spray the fryer with water or use water jets to clean the fryerNOTICE TO U.S. CUSTOMERS NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS U.S Navy Surface Ship Electric Fryers Installation, Operation, Service, and Parts Manual TABLE OF CONTENTS 1.2 Safety Information NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 1 INTRODUCTION1.1 General RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE 1.4 Shipping Damage Claim Procedure1.5 Service Information 1.3 Controller Information NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONS 2.1 IntroductionDo not block the area around the base or under the fryers The contacts CANNOT have an external voltage applied 2.2 Power RequirementsDo not connect the contacts in series Do not connect more than one fryer to each set of contacts 2.3 Installation 2.5 Dimensions and Weights2.4 After Fryers Are Anchored At the Frying Station DANGER BACK OF FRYER UNIT 2-Fryer BatterySingle Fryer FRONT HANDLE 62.55 3-Fryer Battery4-Fryer Battery 2.470 NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 3 OPERATING INSTRUCTIONS 3.1 Equipment Setup and Shutdown Procedures 3.2 Operation of the Solid-State Analog Controller ShutdownDESCRIPTION properly filled with oil. See Section CONTROLLER OPERATING PROCEDURE HIGH-LIMIT TEST PROCEDUREThe analog controller has no timing features. The operator must monitor shake and pull times 5. Place the controller power switch in the OFF position NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS 4.1 Introduction4.2 Preparing the Filter for Use 3. Place the metal filter screen in the center of the bottom of the pan, then lay a sheet of filter paper on top of the screen, over- lapping on all sides 4.3 Operation of the Filter DANGER 2. Remove the basket support rack from the frypot, raise the element assembly to the up position, and snap the Power Shower into position 6. Lower the elements into the frypot and reinstall the basket support rack. Ensure the drain valve is fully closed. If the drain valve is not fully closed, the fryer will not operate. Turn the fryer ON and allow the cooking oil to reach setpoint 4.4 Draining and Disposing of Waste Oil 5.1.2 Clean the Built-in Filtration System - Daily NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 5 PREVENTIVE MAINTENANCE5.1 Cleaning the Fryer DANGER 5.1.1 Clean Inside and Outside of the Fryer Cabinet - Daily 5.1.3 Clean the Frypot and Heating Elements - Weekly DANGER Boiling-Out the Frypot2. Press the fryer ON/OFF switch to the ON position 5.1.4 Clean Detachable Parts and Accessories - Weekly 5.2 Check Calibration of Temperature Control Knob - Monthly5. Turn the fryer ON/OFF switchs to the OFF position 5.3 Annual/Periodic System Inspection FryerBuilt-In Filtration System Check filtration system integrity as follows − Verify that filter pan cover is present and properly installed Verify that frypot drain valves are fully closed NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTING6.1 Introduction Verify that power is connected and that circuit breakers are on Corrective Action Problem6.2 Troubleshooting 6.2.1 Control and Heating Problems Probable Causes Probable Causes 6.2.3 Filtration Problems 6.2.2 Error Messages and Display Problems Filter pump runs 6.3 Replacing the Controller or Controller Wiring Harness NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 7 SERVICE PROCEDURES 7.1 General7.2 Replacing a Controller 7.3 Replacing Component Box Components 7.4 Replacing a Temperature Probe or High-Limit Thermostat DO NOT drain more than one full frypot into the SDU at one time1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit SDU or other appropriate container 7.5 Replacing a Heating Element viewed from the rear 7.7 Replacing a Frypot 7.6 Replacing Contactor Box Components 12. Disconnect the oil return flexlines at the frypot ends 22. Reinstall the drain tube assembly Sediment Particle Oil Flow Up for reverse Down for forward 7.8.2 Replacing the Filter Motor, Filter Pump, and Related Components 7-10 7.8.3 Replacing the Filter Transformer or Filter Relay Test 7.9 Interface Board Diagnostic ChartDiagnostic LED Legend Meter Setting 8051421F 7.10 Wiring Diagram, SystemRefer to page 2-2 for power requirements 7-13 7-14 7.11 Wiring Diagram, Contactor Box 7.12 Components Description of Operation Accessories NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 8 PARTS LIST 8.2 Cabinetry 106-3036SP Side, Cabinet Single Left Use 212-8479 for Rt. SideHandle Grab Rail For handle end use Top Cap Single Top cap for five station fryer shown 8.2.2 Cabinet Bases, Braces, and Associated Parts 8.2.2 Cabinet Bases, Braces, and Associated Parts cont Upright Assembly, Left Use 106-3828 for singlesUpright Assembly, Right Use 106-3829 for singles Channel, Base Rear Use 106-4901 for singles base assembly 8.3.1 Drain Tube Sections and Associated Parts 8.3 Drain System Components 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts See Page 8-10 for DrainValve Detail EURO-LOOK 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts cont 8.3.2 Drain Valve Assembly and Component Parts Page ITEM EURO-LOOK 8.4 Electronics and Wiring Components 8.4.1.1 Single Component Box 8.4.1.2 Multiple Vat Component Boxes 8.4.2.1 Single Contactor Box 8.4.2.2 Multiple Vat Contactor Boxes 8.4.3 Heating Element Assembly and Associated Parts 8.4.3 Heating Element Assembly and Associated Parts cont 8.4.4 Wiring8.4.5.1 Contactor Box Wiring Assembly - 12-Pin Full-Vat C-1 8.4.5.2 Contactor Box Wiring Assemblies - 6-Pin Left Element P/N 106-3467SP 14/17kW or P/N 106-2472SP 22kW 8.4.5.3 Contactor Box Wiring Assemblies - 9-Pin Right Element8.4.5.4 Single Contactor Box Wiring Assembly 8.4.5.5 Main Wiring Harness 8.4.5.9 Single Component Box Wiring Harness - 15-Pin without Filter 8.4.5.6 Single Main Wiring Harness8.4.5.7 Component Box Wiring Harness - 15-Pin 8.4.5.8 Single Component Box Wiring Harness - 15-Pin 8.5.1 FPH117/122 Filtration Components 8.5 Filtration System Components 8.5.1 FPH117/122 Filtration Components cont 8.5.2 FPH217/317 Multiple Battery Filtration System Components units were configured this wayNOTE Some early production Lid for units built before Feb 04, use 8.5.2 FPH217/317 Multiple Battery Filtration System Components contSTANDARD EURO-LOOK 8.6 Frypot Assembly and Thermostat Frypot P/N 823-2451SPThermostat P/N 8.7 Oil Return System Components 8.7 Oil Return System Components cont COMPONENT 8.8 WIRING CONNECTORS, PIN TERMINALS, AND POWER CORDSPower Cords Connectors Tech Support SERVICE HOTLINEShipping Address 8700 Line Avenue, Shreveport, Louisiana FAX Parts