Operating Requirements | IBM 6645, 6644, 6646 manual

Operating Requirements

All machines require two power inputs: one for the system unit and one for the monitor display.

The system units come with a voltage selector switch, allowing selection of voltage of either 115 Vac or 230 Vac. This switch must be in the 230 Vac position when the machine is plugged into a 230 Vac electrical outlet.

The required power input for the monitor (Not included with some models) shipped with the system unit is auto-sensing type and does not require any voltage switch adjustment.

28 IBM Desktop System HMM

Image 60

IBM 6645, 6644, 6646 manual Operating Requirements

Contents

Hardware Maintenance Service for Service Level a 6644/6645/6646Page Contents Check Procedures Diagnostic AidsRepair Information Parts/Test Point Locations Safety Inspection Guide 119 Parts Catalog 121Appendix A. FRU Number List 133 Index 137 Page Voltage Supply Switch Settings Voltage Supply Range Voltage Switch Setting Safety Information To Connect To Disconnect Do not Para Conectar Para Desconectar Cuidado XII Page XIV Page XVI Connexion Déconnexion Xviii Vorsicht Achtung Kabel anschließen Kabel lösen Vorsicht Pericolo Attenzione Per collegare Per scollegare Xxiv Page Xxvi Peligro Instrucciones de Conexión Desconexión Xxviii Page Laser Compliance Statement Trademarks HelpCenter Preface General Information Introduction Product Overview Introduction Product Overview Processors Machine TypeProcessors Machine Type 6645/6646 Memory External Ports Hard Disk DriveCD-ROM Drive Multimedia Power Management Power SupplyInternal Cabling Keyboard Hardware Interfaces Interface Cmos Reset Power-On Password Flash Bios Update Procedure BIOS-contained Model Number and Serial Number Press Y, then press Enter. When the screen showsPress Y, then press Enter IBM Desktop System HMM When the screen shows Bios Configuration/Setup Utility Working with the Setup MenusStarting the Configuration/Setup Utility Changing Parameter Settings Keys Function Save Settings Restore SettingsLoading Default Settings Exiting Setup Viewing System Information, and Product Data USB Boot device Video SetupDevices and I/O ports IDE Drive Setup Palette SnoopingVideo Interrupt IDE Hard Disk Drive Audio Setup IDE CD-ROM DriveAudio Support Network Setup Startup OptionsStartup Sequence Power-On Self Test Power-On LogosAutomatics Power-on Startup Sequence Error Startup Sequence System Security Remote Administration Power-On passwordSecurity Profile by Device Changing the Power-On Password Enter Setup Key in your current password when promptedDelete Power-On Password Advanced Setup Administrator PasswordAdapter ROM Security Asset ID PCI Control Plug and Play Control Plug and Play Operating SystemProcessor Control Wake on LAN Acpi Bios IRQ Specifications Dimension width x depth x heightWeight Environment Operating Requirements Check Procedures Introduction Important The drives in the system you are Check Procedures Start Read the Following Page 005 007 009 Index of Symptoms, Messages, Error Codes, or Beeps Page Post Error Codes and Messages List Bios Error Codes Action/FRU Messages Bios ROM Post Error Codes and Messages List Dimm ROM Post Error Codes and Messages List Post Error Codes and Messages List Bios Error Beeps List Bios Error Beeps Action/FRU Dimm Bios Error Beeps List Error Symptoms List Error Symptoms Action/FRU Processor / Processor FanSystem Board and Memory Error Symptoms Action/FRU Hard Disk Drive CNN1 CD-ROM Drive Error Symptoms List Error Symptoms Action/FRU Real-Time Clock Video and MonitorUSB Ports Some or all keys on Keyboard on Keyboard do not work Other Problems Troubleshooting Factory-Installed Storage Devices 003 Select Utility from the menu 005 Page Audio Not Supported by Diagnostics Program Ensure that Windows 2000 is properly installed EndPerform the following under Windows Check Procedures 004 Select Settings, then select Control Panel 006 008 CD-ROM Drive Try reading the CD with a known good CD-ROM driveReplace system board IBM Desktop System HMM Replace CD-ROM drive End Check Procedures Memory Follow the screen instructions to run the Memory test Keyboard 002 Mouse Test right left button and check if right left button worksTest mouse cursor movement Mouse is functioned normally End Try with a known good mouse 010Replace the mouse End 011 Power Supply Disconnect the power cord from the back of the system unit Pin power connector IDE power connector Replace the on/off switch cable assemblyReplace the power supply End Check Procedures Monitor Is the Screen READABLE? YES, Read AHEAD. NO, GO to Step Is the Screen Still not READABLE? Undetermined Problems DimmPage IBM Desktop System HMM Diagnostic Aids Introduction Power-On Self Test Page Diagnostic CD Using the Diagnostic CD Using Diagnostic Program from Recovery CD Diagnostics Program Features Main Menu Selections Submenu Selections Diagnostic Program Main Menu Selections System Board System Backup Battery Repair Information Removals and Replacements Cover Processor and Fansink Page IBM Desktop System HMM Memory Dimm Adapter Card Internal Speaker USB Port CD-ROM Drive Page Hard Disk Drive Page Power Supply Power Button/Indicator LED and Cable System Board System Backup Battery Handling ESD-Sensitive Parts Software Recovery Procedure Parts/Test Point Locations Introduction 104 Introduction System Board Jumpers Connectors System Board Jumper SettingsJumper/Settings Function System Board Connector Functions Connector Function Connect to Power Supply Connectors and Voltages Power supply Pin Power Connector Pin-hole side viewPower Supply Output Pin Assignment Pin Voltage Cable Color +5Vdc Green Ground Black No connect Red Network Cards In. Hard Disk Drive Jumper Settings Maxtor Hard Disk Maxtor Hard Disk Drive Jumper Settings J50 DescriptionPage Lite-on BTC CD-ROM Front Panel Introduction CD-ROM Drive Rear Panel Connectors and Jumpers CD-ROM Drive Rear Panel Connectors and JumpersFunction Connect to Dimm Configurations System Board Connector Pin Signals Monitor Port SignalsIDE Cable Connector Signals Pin Signal Name IBM Desktop System HMM Safety Inspection Guide General Guidelines 120 Safety Inspection Guide General Guidelines Parts Catalog Abbreviations Country Language Version System Assembly Assembly 1a System Unit- Interior Index Number 6644 6645 6646 Bezel Blank Assembly 1b System Unit Exterior Assembly 2 Hard Drive Assembly 3 CD-ROM Drive Assembly 4 Power Cord ANZ Assembly 5 Keyboard and Mouse US/CAN/ANZ IBM Desktop System HMM FRU Number List FRU Number Asm-Index 1a-2 123 FRU Number List IBM Desktop System HMM Audio Check Procedure Audio Setup Index Pbsram Page