Turning the Copier On, Power Saver | Konica Minolta 2223 instruction

Copier Information

Turning the Copier On

1 Turn ON the main power switch, located on the left front of the copier and wait approximately 65 seconds for copier to warm up.

2 When warm up is completed, the START PRINT light changes from amber to blue-green and the copier is ready to copy using initial machine settings.

NOTE: To conserve energy, be sure to turn off the copier at the end of the workday.

Power Saver

There are two modes for the power saver as described below.

Auto Low Power mode:

The mode conserves energy by lowering the temperature setting of the fixing unit. This provides a two-fold compatible function that serves to minimize energy consumption and maximize copying performance.

Shut-Off mode (Auto/Manual):

The mode conserves energy by partially turning OFF the power supply. The copying performance of this mode is inferior to the conservation can be achieved.

CAUTION

To prevent accidents, shut off power when copier is not expected to be used for a long period; at night, for example.

3-10 Copier Information

Image 31

Konica Minolta 2223 user manual Turning the Copier On, Power Saver

Contents

User’s Manual Konica 2223 Copier Konica 2223 User’s Manual Table of Contents Basic Copying Paper Specifications Duplex Copying Maintenance and SuppliesSpecial Copying Glossary Specifications Troubleshooting Introduction Optional Equipment FeaturesCopier Highlights Standard Equipment To the User Using this Manual Safety Information Canadian Department of Communications Regulations FCC Regulations User Instructions Safety Alert Symbols Machine Safety Labels Safety Information Temperature and Humidity Installation Requirements Plug Socket Power Source Information Internal Machine Components Machine Handling and Care Service Codes Power Saver Check for Routine Safety CheckSpecial Concerns Copier Information Automatic Settings External View Konica 2223 Copier Main Body Internal View Options Control Panel Copier Information Site Requirements Copier Information Turning the Copier On Power Saver Manual Shut-Off Auto Low PowerAuto Shut-Off Initial Machine Settings Automatic SettingsAutomatic Paper Selection APS Automatic Humidity Sensor Odd-Even Original Counter in 1 s 2 ModeAutomatic Exposure Selection AES Automatic Magnification Selection AMS Paper Specifications Copy Paper in Main Body Trays Originals on Platen GlassOriginals on Reversing Automatic Document Feeder Radf Originals on Automatic Document Feeder ADF Copy Paper in 10-Bin Off-Line Stapler Sorter ST-103 Copy Paper and Special Stock in BypassCopy Paper in Automatic Duplex Unit ADU Copy Paper in 10-Bin In-Bin Stapler Sorter ST-104 Paper Size/Weight Compatibility Chart Copy Size Lens Modes Basic Copying Copying from the Platen Glass Basic Copying Auto Copy Copying from the Document Feeder RADF/ADF Copying Mixed Size Originals Bypass Performance Maximum skew 2% Using the Bypass Manual Density Copy Density Copy Size Lens Modes Preset and User Preset Ratios Programming a User Preset Ratio Zoom Mode Special Ratio Table Specifications 10-Bin In-Bin Stapler Sorter ST-104 Using the Sorter Sort Mode with Off-Line Stapler Specifications 10-Bin Off-Line Stapler Sorter ST-103 Stapler Sheet Capacity 20 lb 25 sheets Specifications 20-Bin Off-Line Stapler Sorter ST-216 Group Mode Sort Mode Automatic In-Bin Stapling Staple-Sort Modes for ST-104Manual In-Bin Stapling Off-Line Stapling Option Automatic Duplex Duplex Copying Automatic Duplex 1s2 Mode Using the RADF/ADF Odd-Even Original Counter OFF 1s2 Mode Using the RADF/ADF Odd-Even Original Counter on 1s2 Mode Using the Platen Glass 2s2 Mode Using the Radf 2s1 Mode Using the Radf Manual Duplex Sided to 2-Sided Using the Bypass Duplex Copying Special Copying Shift/Reduce & Shift Using the Platen GlassShift Result Using the RADF/ADF Frame and Fold Erasure Using Frame and Fold Erasure Setting Frame Erasure Setting Fold Erasure Sheet Size Book Copy Photo Enhance OHP Interleave Service, Supplies, and Repairs Daily Maintenance Maintenance and Supplies Service, Supplies, and Repairs Maintenance and Supplies Cleaning the RADF/ADF Conveyance Belt Surface Daily MaintenanceCleaning the Platen Glass Cleaning the Inner Surface of the Platen Cover Removing/Inserting Paper Trays Cleaning the Corona Wire Loading Paper Service-Adjustable Tray Tray 1, 2 LCT Large Capacity Tray Tray User-Adjustable Tray Option Adding Toner Maintenance and Supplies In-Bin Stapler Replacing the Staple Cartridge Off-Line Stapler Removing the Off-Line Corner Stapling Adapter Installing the Off-Line Corner Stapling Adapter Example Print Quantity Window Preventive MaintenanceReading the PM Count Example Message Area Moving the Copier Troubleshooting Opening and Closing the Copier Troubleshooting User Codes Mishandled Paper Codes Copier Diagram Code J11 Clearing Mishandled Paper Code J12 Code J13 Code J14 Code J15 Codes J31 and J16 When using the bypass Fixing unit is very hot. To avoid burns, do not touch it Code J32 Code J61 Code J62 Code J72 ST-103/ST-216 Code J72 ST-104 Code J92 Code J94 Code J93 Code J95 Reporting Service Codes Service Codes In-Bin Stapler Code J75 Clearing a Wedged Staple Off-Line Stapler Close the stapler Copy Image is TOO Light Troubleshooting Hints ADD Paper is Displayed in Message Area Copy Size Indicator is Flashing Glossary Glossary Document Feeder see Automatic Document Feeder Image Shift see Shift Glossary G-5 Glossary Glossary G-7 Glossary Glossary G-9 Specifications APS AMS Specifications