Illegal Command F8=0 | SDI Technologies SDIO Card specification

©Copyright 2000-2007 SD Card Association

SDIO Simplified Specification Version 2.00

Re-init Memory

MEM=0

Illegal Command

F8=0

	Power On	Re-init IO
	IO=0, MEM=0	IO=0
	CMD0 CS=Low	CMD52 IO Reset
	CMD8	CMD8 is required to support
	CMD8	High Capacity Memory.
		High Capacity Memory.
	Check Response	Error Response
	Check Response
	Good Response
	F8=1	Unusable card
		Unusable card

Skip IO Initialize or IO=1

Test IO Flag

Execute IO Initialize & IO=0

CMD5 Arg=0

Get IO OCR

Illegal Command	Check Response		NF=0 or OCR invalid
	Check Response
	NF>0 & OCR valid
	Set New Voltage (if needed)
	CMD5 Arg=WV
IORDY=0	Check Response		1sec Timeout
	Check Response
	IORDY=1
	IO=1	IO Initialized
	Test MP		MP=0
	Test MP
	MP=1
	C		D

8

Image 17

SDI Technologies SDIO Card manual Illegal Command F8=0

Contents

SD Specifications Part E1 Sdio Simplified Specification Date Version Sdio Simplified Specification VersionChanges compared to previous issue Release of SD Simplified Specification Conventions Used in This Document Table of Contents SPI and SD 1-bit Mode Interrupts 16.2 Table of Tables Table of Figures General Description Sdio FeaturesPrimary Reference Document Standard Sdio Functions Sdio Card Types Sdio Signaling DefinitionSdio Card modes Sdio Host Modes Signal connection to two 4-bit Sdio cards Signal Pins Differences in I/O card Initialization ResetSdio Card Initialization Sdio Simplified Specification Version MEM=0 Card initialization flow in SD mode Sdio aware host Illegal Command F8=0 Card initialization flow in SPI mode Sdio aware host VDD Voltage Window Position Iosendopcond Command CMD5OCR Values for CMD5 OCR bit Iosendopcond Response R4 Response R4 in SD mode Recommendations for RCA after Reset Acceptable Commands after InitializationSpecial Initialization considerations for Combo Cards Re-initialize both I/O and Memory Re-Initialization Flow for Memory controller Re-Initialization Flow for I/O Controller Enabling CRC in SPI Combo Card Unsupported SD Memory Commands Differences with SD Memory SpecificationSdio Command List Bus Width Reset for SdioModified R6 Response Timings Card Detect ResistorCombo Card 4-bit Control Card Detect Resistor States Data Transfer Abort Data Transfer Block SizesChanges to SD Memory Fixed Registers Read Abort CID Register OCR RegisterCSD Register RCA Register Bit Identifier Type Value Description Sdio Status Register StructureClear Iorwdirect Command CMD52 New I/O Read/Write Commands Illegalcommand ComcrcerrorIorwdirect Response R5 1 CMD52 Response SD modes Identifier Type Value Description Clear Condition DIS=DisabledCMD=DAT lines free TRN=Transfer Iorw Extended command Op Code Definition Iorwextended Command CMD53OP code Command operation CRC 1 CMD53 Data Transfer Format Byte Count Values Sdio Card Internal Operation Register Access TimeOverview Interrupts Read Wait Suspend/ResumeCMD52 During Data Transfer Sdio Fixed Internal Map Card Common Control Registers Cccr Common I/O Area CIA Type Card Common Control Registers CccrCCCR/SDIO IOE3 To abort transfers to/from memory Scsi 4BLS Transaction of function 0 CIA Empc Cccr bit Definitions Address Function Basic Registers FBRFunction Basic Information Registers FBR Field Type FBR bit and field definitions Sdio Simplified Specification Version Field Type Card Information Structure CIS Setting Block Size with CMD53Multiple Function Sdio Cards Card Information Structure CIS and reserved area of CIA State Diagram for Bus State Machine Bus State Diagram CSA Data Format CSA AccessEmbedded I/O Code Storage Area CSA Interrupt Timing Sdio Interrupts Interrupt Clear Timing Terminated Data Transfer Interrupt Cycle Sdio Suspend/Resume Operation Sdio Read Wait Operation Power Control Overview Power ControlPower Control support for Sdio Cards Master Power Control Power Selection Power Control Support for the Sdio HostHigh-Power Tuples Reference Tuples by Master Power Control and Power Select Power Control Operation Switching Bus Speed Mode in a Combo Card High-Speed ModeSdio High-Speed Mode Sdio Physical Properties Sdio Power Sdio Simplified Specification Version Inrush Current Limiting CIS Reference Document CIS FormatsBasic Tuple Format and Tuple Chain Structure Byte Order Within Tuples Sdio Card Metaformat Tuple VersionTuples Supported by Sdio Cards Code Name Description Sdio Specific Extensions Cistplmanfid Manufacturer Identification String TupleCistplmanfid Manufacturer Identification Tuple Cistplfuncid Function Identification Tuple Cistplfunce Tuple General Structure Cistplfunce Function Extension TupleCistplfunce Tuple for Function 0 common Tplfidfunction Tuple for Function 0 common Byte Cistplfunce Tuple for FunctionTplfidfunction Tuple for Function Sdio Simplified Specification Version 10 Tplfefunctioninfo Definition Tplfidfunction Field Descriptions for Functions11 Tplfecsaproperty Definition Bit Name 12 Cistplsdiostd Tuple Reserved for Sdio Cards Cistplsdiostd Function is a Standard Sdio FunctionCistplsdioext Tuple Reserved for Sdio Cards 13 Cistplsdioext Tuple Reserved for Sdio Cards Normative SD and SPI Command ListTable A-14 SD Mode Command List Sdmem Sdio Table A-15 SPI Mode Command List Normative References Appendix B Abbreviations and Terms Appendix C LOW, High Informative