Scsi ID Setting | Tandberg Data Tandberg LTO2 specs

2.5Switching ON the Power Switch and the Power-On Sequence

Switching ON the power of the Autoloader executes an automatic power-on sequence.

1.Connect the AC power cable.

2.Press the right side ( ) of the Autoloader front panel power switch to switch the power ON.

3.When the power is supplied, the POWER LED lights in green and the power-on test starts.

4.When the power-on test ends normally, "READY" and "DRV empty" are alternately displayed on the top level of the LCD.

Power switch

Figure 2-6 Powering on the LTO2 Autoloader

2.6 SCSI ID Setting

Please check that the SCSI ID of the Autoloader is not already being used by a server/workstation or another SCSI device. (Prior to shipping from the factory, the SCSI ID of the Autoloader was set as described below.)

See "3.6 Setting the SCSI ID" for information about how to check the SCSI IDs that have been set and for the method of changing them when required.

Important

The Autoloader and the tape drive must each have an independent SCSI ID. This device has a specification that does not allow duplication of the tape drive and Autoloader IDs. Please check that the IDs of other SCSI devices on the same SCSI bus do not duplicate the IDs of the tape drive and the Autoloader.

SCSI ID at time of factory shipping ●	Tape drive	:	(1)
●	Autoloader	:	(0)

- 12 -

Image 28

Tandberg Data Tandberg LTO2 manual Switching on the Power Switch and the Power-On Sequence, Scsi ID Setting

Contents

Tandberg LTO2 Autoloader FCC Class B Notice Trademarks Safety Descriptions Description example in this manual Prohibited action Mandatory action Safety Cautions General Cautions Do not apply starburst wiring Do not cover the air inlet Do not lift the device alone Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Troubleshooting Chapter Daily MaintenanceChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 Autoloader Names and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCD Handling Precautions Transfer or Disposal of the DeviceMain Unit Cartridges Contents of the Carton Preparation Before Use SetupTransporter Locking Screw Instruction TAG Scsi Cable Connections Storing the Transporter Locking Screw for later use AC Power Cable Connection AC Power Cable Connection Attaching and removing the Filter Element Attaching and removing a Filter Element Switching on the Power Switch and the Power-On Sequence Scsi ID Setting Start and Shutdown of the System Operation Removal of the Magazine Loading the Magazine Loading the Magazine Loading the Cartridge Loading to Magazine Loading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCRs optionalOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the Magazine Removal from and Insertion to the Fixed Slots Display Eject Slot? Organization of the Front Panel Switches Functions of the SwitchesOperation of the Panel Keys Slot Logical Numbers Panel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main Menu Retry Mode Setting the Scsi ID Checking the Scsi ID Changing the Scsi ID Operation Example Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Cleaning Cartridge Data Cartridge Write-Protect Switch Setting the Write-protect Switch Using Bar Code Labels Precautions Bar Code Label Usage Precautions General Precautions Standards for Prohibition of Use Service LifeStorage of Data Cartridges Cleaning Daily MaintenanceCleaning of the Drive Head Manually Cleaning of the Drive Head Default CLNROL-function setting Enable Cleaning the Roller inside of the transporterChecking the CLNROL- function Setting the CLNROL- function Disable RtyCnt value in the CLNROL-function Changing the RtyCnt valueOperation Example Tip Cleaning of the Roller Execution timing of the cleaning Tools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the Roller Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the Main Unit Cleaning of the exteriorCleaning of the fixed slots Cleaning of the interior Cleaning of the magazine Cleaning of the cartridge Movement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power Supply Phenomenon Recovery Procedure Cartridge Operation Connections Cleaning Phenomenon Recovery Procedure Autoloader PerformanceOthers Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to Check Appendix a Specifications Autoloader Main Unit Universal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Optional Items Appendix B Optional Items and SuppliesSupplies Appendix C Error Code CMer Error Code Err ×××× Messages Messages Related to the Drive Interface Panel Operation and Other Messages Message Description Tandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway