ADSL2/2+ Ethernet Router User Guide | TP-Link TD-8816 specification

Image 27

TP-Link TD-8816 manual ADSL2/2+ Ethernet Router User Guide, If you select Disabled, the DHCP function will not take effect

Contents

Rev1.0.2 1910010149 TD-8816 ADSL2/2+ Ethernet Router COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENT Package Contents Chapter 1. Introduction CONTENTSChapter 2. Hardware Installation Chapter 3. Quick Installation Guide 4.6.5 Appendix A SpecificationDiagnostic 4.6.4 ADSL 1.2 Main FeaturesChapter 1. Introduction 1.1 Product Overview 1.3 Conventions LED Explanation Chapter 2. Hardware Installation2.1 The Front Panel 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation Environment ADSL2/2+ Ethernet Router User Guide 3.1 Configure PC Chapter 3. Quick Installation Guide ADSL2/2+ Ethernet Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start 4.1 Status Chapter 4. Software Configuration 4.3 Interface Setup 4.2 Quick Start4.3.1 Internet the next screen shown in Figure ¾ TCP MTU Option Enter the TCP MTU as your desire 1. Dynamic IP Address for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format 2. Static IP Address3. PPPoA/PPPoE ADSL2/2+ Ethernet Router User Guide 4. Bridge Mode 4.3.2 LAN ADSL2/2+ Ethernet Router User Guide IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function 4.4.3.1. DMZ4.4.3.2. Virtual Server Other configurations for the entries as shown in Figure Server in the next screenTo add a virtual server entry To add a mapping rule 4.4.3.3. IP Address Mapping 4.4.4 QoS 4.4.5 VLAN can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows 1. Assign VLAN PVID for each Interface2. Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management 4.5.2.1. IP Filter 4.5.2 Filter ¾ Interface Select the interface for the entry To add an IP Address filtering entry ¾ Rule Type For IP Filter, please select IP here 4.5.2.2. MAC Filter Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.3. Application Filter Step 4 Finally, click the SAVE to save the entry 4.5.2.4. URL ¾ Application Filter Activate or deactivate the function To add a URL filter entry 4.5.3 SNMP 4.5.5 DDNS 4.5.4 UPnP 4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance 1. NTP Server automatically 4.6.2 Time Zone 4.6.3 Firmware 2. PC’s Clock3. Manually To upgrade the routers firmware, follow these instructions below 4 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings To restore the Router’s settings 4.6.4 System Restart 4.7 Help 4.6.5 Diagnostic ADSL2/2+ Ethernet Router User Guide Appendix A Specification GeneralPhysical and Environment