Husqvarna 136, 141 Limbing and Pruning, Bucking Without a Support, Using a log for support

Page 12

BUCKING WITHOUT A SUPPORT

•Overcut through 1/3 of the diameter of the log.

•Roll the log over and finish with a second overcut.

•Watch for logs with a compression side to prevent the saw from pinching. See il-

lustration for cutting logs with a compres- sion side.

BUCKING USING A LOG OR SUP- PORT STAND

•Remember your first cut is always on the compression side of the log. (Refer to the illustration below for your first and second cuts).

•Your first cut should extend 1/3 of the diameter of the log.

•Finishwith yoursecond cut.

Using a log for support

2nd Cut

--.. : --- lstCut

2nd Cut

Using a support stand

2nd Cut

1st Cut

/

L

LIMBING AND PRUNING

Ka, WARNIN(5: Be alert for and guard

against kickback. Do not allow the moving chain to contact any other branches or ob- jects at the nose of the guide bar when limb-

ing or pruning. Allowing such contact can re- sult in serious injury.

4[_WARNING: Never climb into a tree

to limb or prune. Do not stand on ladders, platforms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

•Work slowly, keeping both hands firmly gripped on the saw. Maintain secure foot- ing and balance.

•Watch out for springpoles. Use extreme caution when cutting small size limbs. Slender material may catch the saw chain and be whipped toward you or pull you off balance.

•Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

•Keep a clearwork area. Frequentlyclear

branches out of the way to avoid tripping over them.

LIMBING

• Alwayslimbatreeafteritiscutdown. Only then can limbing be done safely and prop- erly.

•Leave the larger limbs underneath the felled tree to support the tree as you work.

•Start at base of the felled tree and work to-

ward the top, cutting branches and limbs. Remove small limbs with one cut.

•Keep the tree between you and the chain. Cut from the side of the tree opposite the branch you are cutting.

•Remove larger, supporting branches with

thecuttingtechniquesdescribed in BUCK-

ING WITHOUT A SUPPORT.

•Always use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch saw.

PRUNING

'A_WARNING: Limit pruning to limbs

shoulder height or below. Do not cut if branches are higher than your shoulde_ Get a professional to do the job.

•Make your first cut 1/3 of the way through the bottom of the limb.

•Next make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1to2 inch collarfrom thetrunkofthe tree.

i ll'i Secon,_cu_/

Zhird_t _ _'

ColIVI_. _ First cut

(' Pruning technique

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Husqvarna ON/OFF Plan Ahead Operate Your SAW SafelyMaintain Your SAW in Good Working Order JustmentsAvoid Pinch-Kickback Avoid Pull-InReduce the Chance Kickback Maintain ControlKickback Safety Features Chain Brake and CKA AngleBAR ChainStandards Adjusting the tension Diirection of RotationChecking the tension Fueling Engine Handle Fuel with Caution BAR and Chain LubricationImportant points to remember ON/STOP Switch CHOKE/FAST Idle Lever Chain BrakeStarting a Warm Engine Difficult Starting or starting a flooded engineImportant Points Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Bucking Cut only one log at a timeTypes of Cutting Used for Bucking Using a log for support Using a support standLimbing and Pruning Bucking Without a SupportMaintenance Schedule Carburetor AdjustmentsBAR Maintenance AIR FilterStorage TroubleRemedy Limited Warranty Husqvarnas OBLIGA- Tions Under the WarrantyItems not Covered by this Warranty Exceptions and LIM- ItationsProcedure to OB Tain Warranty Consideration Your Warranty Rights and OBCustomer RE Sponsibilities Statesville RoadWhere to GET Warranty Service Placement and Repair of EmissionMaintenance Statement The owner Tor, Ignition System Spark Plug covered upHusqvama
Related manuals
Manual 4 pages 16 Kb Manual 5 pages 61.56 Kb

141, 136 specifications

The Husqvarna 141 and 136 chainsaws are remarkable tools designed for both homeowners and forestry professionals, offering reliable performance and ease of use. These models are particularly well-suited for light to moderate cutting tasks, making them ideal for trimming bushes, felling small trees, and cutting firewood.

One of the key features of the Husqvarna 141 and 136 is their lightweight design, which facilitates effortless maneuverability. Weighing in at around 10.5 pounds, these chainsaws are easy to handle for extended periods, reducing fatigue during prolonged use. This is especially beneficial for users who may not have extensive experience with chainsaws.

Another highlight of these models is the powerful engine. The Husqvarna 141 is equipped with a 40cc engine, while the 136 features a slightly smaller 35cc engine. Both engines utilize a two-stroke design that maximizes performance and efficiency. The X-Torq technology integrated into these models minimizes harmful emissions and enhances fuel efficiency, making them environmentally friendly options in the market.

In terms of safety features, both chainsaws come with a chain brake that is activated in the event of kickback, providing an extra layer of protection for the operator. The anti-vibration technology significantly reduces vibrations, allowing for more comfortable operation and limiting operator fatigue.

The easy-start system is another practical feature of the Husqvarna 141 and 136. This system helps users start the chainsaw with minimal effort, ensuring that you can get to work quickly without dealing with frustrating starting issues. Additionally, both models feature an adjustable oil pump that allows the user to control the amount of oil delivered to the chain, which ensures optimal lubrication and extends the life of the chainsaw.

Maintenance is straightforward with the Husqvarna 141 and 136, thanks to tool-less chain tensioning and a quick-release air filter. This design simplifies the process of adjusting the chain and cleaning the air filter, ensuring that the chainsaw remains in peak working condition.

In summary, the Husqvarna 141 and 136 chainsaws deliver a blend of lightweight design, powerful engines, advanced technologies, and essential safety features. These models are an excellent choice for those looking for a reliable and efficient tool for various cutting tasks around the home or for light commercial use.
Top Page Image Contents