Husqvarna 576XP AutoTune Needle bearing lubrication, Adjustment of the oil pump, Cooling system

Page 34

MAINTENANCE

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open.

Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

Recommended settings:

Bar -15": 1 turn from the closed position.

Bar 15" -18": 2 turns from the closed position.

Bar 18" -24": 3 turns from the closed position.

Bar 24" -: 4 turns from the closed position.

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil flow by one step.

 

!

WARNING! The engine must be stopped

 

when making adjustments.

 

 

 

 

 

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the flywheel.

4Cooling fins on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Note! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit.

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburetor passes through the starter. Dirt and dust is pushed out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained. Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburetor compartment.

34 – English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents 576XP AutoTune Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Temperature 0C 32F or colderTemperature -5C 23F or colder Fitting the winterising kitMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges With significantly reduced kickback potential are availableFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+S==¶5\¨ Page 1151292-95
Top Page Image Contents