Husqvarna 460, 455e High speed jet H, Correctly adjusted carburetor, Checking brake band wear

Page 30

MAINTENANCE

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

To adjust the carburetor correctly you should contact a mechanic with access to a rev counter.

CAUTION! As the spark is cut off, the rev counter does not show speeds higher than 13600 rpm.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.6 mm (0,024 inch) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Rancher KEY to Symbols Key to symbolsContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingSharpening cutting teeth Chain oil Tensioning the chainLubricating cutting equipment Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment To prolong the life of the bar you should turn it over daily Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger Muffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springAir filter Spark plugLubricating the bar tip sprocket Needle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemTemperature 0C 32F or colder Temperature -5C 23F or colderWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions´z+H8o¶5u¨ Page 1140247-95 ´z+H8o¶5u¨ ´z+H8o¶5u¨
Related manuals
Manual 44 pages 8.75 Kb

455, 460, 455e specifications

The Husqvarna 460 and 455 series chainsaws are some of the most popular models in their class, recognized for their reliability, performance, and advanced technology. These machines are designed to meet the demands of both professionals and enthusiasts who require powerful tools for cutting firewood, felling trees, or performing tree maintenance.

The Husqvarna 460 is equipped with a robust 60.3 cc engine that delivers impressive power and efficiency. With a power output of approximately 3.6 kW, this chainsaw is capable of handling ambitious cutting tasks with ease. The design of the 460 includes a low-vibration system that significantly reduces operator fatigue during extended use. This is achieved through effective isolating features that dampen vibrations transferred to the user's hands, allowing for more comfortable operation over longer periods.

One of the standout features of the Husqvarna 460 is its X-Torq engine technology. This innovative design reduces fuel consumption by up to 20% while also decreasing harmful exhaust emissions. This is increasingly important for environmentally conscious users, as it allows for a greener operation without compromising performance. The chainsaw is also equipped with an air injection system that effectively removes larger particles from the air before they reach the filtration system, ensuring cleaner air intake and extending the lifespan of the air filter.

On the other hand, the Husqvarna 455 Rancher is another exceptional model known for its versatility and robust design. Featuring a slightly smaller 55.5 cc engine, it offers a solid power output of around 2.6 kW, making it suitable for a wide range of tasks from cutting firewood to clearing brush. The 455 Rancher shares many of the same technological advancements as the 460, including the X-Torq engine and low-vibration technology, providing users with similar benefits in terms of efficiency and comfort.

Both models feature an adjustable oil pump for better chain lubrication, ensuring smooth operation and prolonging the chain's life. Additionally, the easy access air filter and tool-less chain tensioning allow for quick maintenance and adjustments in the field, making them user-friendly choices.

Overall, the Husqvarna 460 and 455 series chainsaws combine power, efficiency, and advanced technology, catering to the needs of both casual users and professionals alike. Their thoughtful design and robust performance establish them as reliable tools in any cutting task, making them a top choice for those in need of high-quality chainsaws.
Top Page Image Contents