Husqvarna 1153158-95 General requirements working at height, Preparing to use the saw in the tree

Page 24

WORKING TECHNIQUES

user. If the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting with a pulling chain gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Working with tree service chain-saws from a rope and harness

This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a rope and harness. While it may form the basis of guidance and training literature, it should not be regarded as a substitute for formal training.

General requirements working at height

Operators of tree service chainsaws working at height from a rope and harness should never work alone. A competent ground worker trained in appropriate emergency procedures should assist them.

Operators of tree service chainsaws for this work should be trained in general safe climbing and work positioning techniques and shall properly equipped with harnesses, ropes, strops, karabiners and other equipment for maintaining secure and safe working positions for both themselves and the saw.

Preparing to use the saw in the tree

The chain saw should be checked, fuelled, started and warmed up by the ground worker and the chain brake should be engaged before it is sent up to the operator in the tree. The chainsaw should be fitted with a suitable strop for attaching to the operator’s harness:

a)choke the strop around the attachment point on the rear of the saw.

b)provide suitable karabiners to allow indirect (i.e. via the strop) and direct attachment (i.e. at the attachment point on the saw) of saw to the operators harness.

c)ensure the saw is securely attached when it is being sent up to the operator.

The saw should only be attached to the recommended attachment points on the harness. These may be at mid- point (front or rear) or at the sides. Where possible attaching the saw to centre rear mid-point will keep it clear of climbing lines and support its weight centrally down the operator’s spine.

When moving the saw from any attachment point to another, operators should ensure it is secured in the new position before releasing it from the previous attachment point.

Using the chainsaw in the tree

An analysis of accidents with these saws during tree service operations shows the primary cause as being inappropriate one-handed use of the saw. In the vast majority of accidents, operators fail to adopt a secure work position witch allows them to hold both handles of the saw. This results in an increased risk of injury due to:

•not having a firm grip on the saw if it kicks back.

•a lack of control of the saw such that it is more liable to contact climbing lines and operators body (particularly the left hand and arm)

•loosing control from insecure work position resulting in contact with the saw (unexpected movement during operation of the saw)

Securing the work position for two-handed use

To allow the operator to hold the saw with both hands, they should as general rule, aim for secure work position where they are operating the saw at:

•hip level when cutting horizontal sections.

•solar plexus level when cutting vertical sections.

Where the operator is working close into vertical stems with a low lateral forces on their work position, then a

24 – English

Page 23 Page 25
Image 24
Page 23 Page 25
Contents 334T 338XPT KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard Throttle lockout Chain catcherVibration damping system Stop switch Cutting equipmentMuffler General rulesBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Checking wear on cutting equipmentAssembly Fitting the bar and chainWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsDo not let go of the handles Using the chainsaw in the tree General requirements working at heightPreparing to use the saw in the tree Securing the work position for two-handed useBasic cutting technique Limbing Felling technique for tree tops Felling directionDirectional cuts General advice Freeing a tree that has fallen badlyFelling cut Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance CarburetorCorrectly adjusted carburetor High speed jet HThrottle lockout Muffler StarterChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocketMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations, model 334T Bar and chain combinations, model 338XPTSaw chain filing and file gauges Federal and California Emissions Control Warranty Your Warranty Rights and ObligationsEmission Warranty Parts List American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage Page Original instructions 1153158-95

1153158-95 specifications

The Husqvarna 1153158-95, known for its robust performance and innovative features, is a standout product in the realm of outdoor power equipment. As part of Husqvarna's reputable lineup, this model showcases advanced technology designed to enhance user experience, efficiency, and safety.

One of the most remarkable features of the Husqvarna 1153158-95 is its powerful engine. Designed for optimal performance, the engine delivers enough power for a variety of tasks, from trimming grass to tackling more demanding landscaping jobs. This reliability ensures that users can complete their tasks efficiently without frequent interruptions.

Another key characteristic of the Husqvarna 1153158-95 is its ergonomic design. The handle is crafted to provide comfort during extended periods of use, reducing fatigue and enhancing control. This attention to user comfort demonstrates Husqvarna's commitment to creating products that cater to the needs of both casual users and professionals alike.

The innovation extends to the cutting technology used in the Husqvarna 1153158-95. Equipped with advanced cutting systems, this model promises clean and precise cuts, which minimizes damage to the grass and promotes healthier lawn growth. The adjustable cutting height feature allows users to customize their mowing experience to suit different types of grass and landscaping needs.

Additionally, the Husqvarna 1153158-95 incorporates safety features that significantly enhance user protection. The auto return stop switch is a standard feature that ensures the engine turns off automatically once the job is done, preventing any accidental activation. Furthermore, the machine's design includes safety guards to protect users from potential hazards while operating.

The technological aspects of the Husqvarna 1153158-95 do not stop with its physical features. Many models in the Husqvarna range also include Bluetooth connectivity for smart device integration, allowing users to track performance metrics and manage maintenance schedules conveniently. This tech-savvy approach positions the Husqvarna 1153158-95 as a forward-thinking choice for environmentally conscious consumers.

In conclusion, the Husqvarna 1153158-95 exemplifies the fusion of power, ergonomics, safety, and technology. With its range of advanced features, this model stands out as an excellent choice for those looking to enhance their outdoor maintenance activities. Husqvarna's dedication to quality and innovation ensures that users will not only meet their landscaping goals but also enjoy a safer and more comfortable experience.
Top Page Image Contents