Husqvarna 1151470-95 manual Cutting equipment designed to reduce kickback, Bar, Chain

Page 11

GENERAL SAFETY PRECAUTIONS

recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or

! the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating

! saw chain can cause extremely serious injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

•Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

•Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

•Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

•Chain pitch (inches)

•Drive link width (mm/inches)

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EPA III 576 XP EPA You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Muffler Stop switchCutting equipment Vibration damping systemChain Cutting equipment designed to reduce kickbackBar General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the front hand guard Correctly adjusted carburetorHigh speed jet H Checking brake band wearImmediately Checking the inertia brake releaseMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning When making adjustmentsHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataYour cutting need Saw chain filing and file gaugesYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions´z+SO¶5¨ Page 1151470-95
Top Page Image Contents