Husqvarna 115 13 82-95 manual Federal Emission Control Warranty Statement

Page 42

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

charge to the owner at an approved Husqvarna Forest &

OBLIGATIONS

Garden servicing dealer. If you have any questions

regarding your warranty rights and responsibilities, you

The EPA (The US Environmental Protection Agency),

should contact your nearest authorized servicing dealer or

Environment Canada and Husqvarna Forest & Garden are

call Husqvarna Forest & Garden at 1-800-487-5951 or visit

pleased to explain the emissions control system warranty

www.usa.husqvarna.com.

on your 2009 and later small nonroad engine. In U.S. and

WARRANTY PERIOD Any warranted part which is not

Canada, new small nonroad engines must be designed,

scheduled for replacement as required maintenance, or which

built and equipped to meet the federal stringent anti-smog

is scheduled only for regular inspection to the effect of “repair

standards. Husqvarna Forest & Garden must warrant the

or replace as necessary” shall be warranted for 2 years. Any

emission control system on your small nonroad engine for

warranted part which is scheduled for replacement as

the period of time listed below provided there has been no

required maintenance shall be warranted for the period of time

abuse, neglect or improper maintenance of your unit. Your

up to the first scheduled replacement point for that part.

emission control system includes Parts such as the

DIAGNOSIS The owner shall not be charged for diagnostic

carburetor and the ignition system. Where a warrantable

labor which leads to the determination that a warranted

condition exists, Husqvarna Forest & Garden will repair

part is defective, if the diagnostic work is performed at an

your small nonroad engine at no cost to you. Expenses

approved Husqvarna Forest & Garden servicing dealer.

covered under warranty include diagnosis, parts and labor.

CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden

may be liable for damages to other engine components

MANUFACTURER S WARRANTY

caused by the failure of a warranted part still under warranty.

COVERAGE

WHAT IS NOT COVERED

The 2009 and later small nonroad engines are warranted

for two years. If any emission related part on you engine

All failures caused by abuse, neglect or improper

(as listed above) is defective, the part will be repaired or

maintenance are not covered.

replaced by Husqvarna Forest & Garden.

ADD -ON OR MODIFIED PARTS

OWNER S WARRANTY RESPONSIBILITIES

The use of add-on or modified parts can be grounds for

As the small nonroad engine owner, you are responsible for

disallowing a warranty claim. Husqvarna Forest & Garden

is not liable to cover failures of warranted parts caused by

the performance of the required maintenance listed in your

the use of add-on or modified parts.

Operators Manual. Husqvarna Forest & Garden recommends

HOW TO FILE A CLAIM

that you retain all receipts covering maintenance on your small

nonroad engine, but Husqvarna Forest & Garden cannot deny

If you have any questions regarding your warranty rights and

warranty solely for the lack of receipts or for your failure to

responsibilities, you should contact your nearest authorized

ensure the performance of all scheduled maintenance. As the

servicing dealer or call Husqvarna Forest & Garden at 1-

small nonroad engine owner, you should, however, be aware

800-487-5951 or visit www.usa.husqvarna.com.

that Husqvarna Forest & Garden may deny you warranty

WHERE TO GET WARRANTY SERVICE

coverage if your small nonroad engine or a part of it has failed

due to abuse, neglect, improper maintenance, unapproved

Warranty services or repairs shall be provided at all

modifications or the use of parts not made or approved by the

Husqvarna Forest & Garden authorized servicing dealers.

original equipment manufacturer. You are responsible for

MAINTENANCE, REPLACEMENT AND

presenting your small nonroad engine to a Husqvarna Forest

REPAIR OF EMISSION-RELATED PARTS

& Garden authorized servicing dealer as soon as a problem

exists. The warranty repairs should be completed in a

Any Husqvarna Forest & Garden approved replacement

reasonable amount of time, not to exceed 30 days. If you have

part used in the performance of any warranty maintenance

any questions regarding your warranty rights and

or repairs on emission-related parts, will be provided

responsibilities, you should contact your nearest authorized

without charge to the owner if the part is under warranty.

servicing dealer or call Husqvarna Forest & Garden at 1-800-

EMISSION CONTROL WARRANTY PARTS

487-5951 or visit www.usa.husqvarna.com.

LIST

WARRANTY COMMENCEMENT DATE

1 Carburetor and internal parts

The warranty period begins on the date small nonroad

2 Intake pipe, airfilter holder and carburetor bolts.

engine is delivered.

3 Airfilter and fuelfilter covered up to maintenance schedule.

LENGTH OF COVERAGE

4 Spark Plug, covered up to maintenance schedule

Husqvarna Forest & Garden warrants to the initial owner

5 Ignition Module

and each subsequent purchaser that the engine is free

MAINTENANCE STATEMENT

from defects in materials and workmanship which cause

The owner is responsible for the performance of all

the failure of a warranted part for a period of two years.

WHAT IS COVERED

required maintenance, as defined in the operator’s manual.

 

REPAIR OR REPLACEMENT OF PARTS Repair or

 

replacement of any warranted part will be performed at no

 

´®z+SF=¶5"¨

´®z+SF=¶5"¨

42 – English

115 13 82-95 Rev.2 2009-03-23

Image 42
Contents 455e Rancher Rancher 460 Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard 115 13 82-95 Rev.2 English Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment 455e RancherFilling with chain oil Needle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Rancher, 460 Rancher AssemblyFitting the bar and chain 455e RancherAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the front hand guard Correctly adjusted carburetorChecking brake band wear Checking the inertia brake releaseThrottle lockout Muffler StarterChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketTemperature -5C 23F or colder Air Injection centrifugal cleaningTemperature 0C 32F or colder Cooling system Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar Chain Bar and chain combinationsSaw chain filing and file gauges Pitch, inchFederal Emission Control Warranty Statement Repair or Replacement of Parts Repair orKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1151382-95