Husqvarna GR41, RS52, RS44, GR50 manual Fuel Handling, Fuel safety

Page 18

FUEL HANDLING

Fuel safety

Never start the machine:

1If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

Transport and storage

•Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers.

•When storing and transporting fuel always use approved containers intended for this purpose.

•When storing the machine for long periods the fuel tank must be emptied. Contact your local petrol station to find out where to dispose of excess fuel.

•Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

•The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage.

WARNING! Take care when handling fuel.

!Bear in mind the risk of fire, explosion and inhaling fumes.

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two- stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Fuel and fuel fumes are highly

!inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation.

Petrol

CAUTION! Always use a quality petrol/oil mixture at least 90 octane (RON). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded petrol/oil mixture. Leaded petrol will destroy the catalytic converter.

Use low-emission petrol, also known as alkylate petrol, if it is available.

•The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.

•When working at continuous high revs a higher octane rating is recommended.

Two-stroke oil

•For best results and performance use JONSERED two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

•A poor oil quality and/or too high oil/fuel ratio may jeopardise function and decrease the life time of catalytic converters.

•Mixing ratio

1:50 (2%) with JONSERED two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines.

Petrol, litre

Two-stroke oil, litre

 

 

2% (1:50)

3% (1:33)

 

 

 

 

5

0,10

0,15

 

 

 

10

0,20

0,30

 

 

 

15

0,30

0,45

 

 

 

20

0,40

0,60

 

 

 

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator′s manual KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what on the clearing saw? GR41/GR50/RS44What is what on the clearing saw? RS52 General Safety Precautions Personal protective equipmentMachine′s safety equipment Stop switchThrottle lockout Quick release Cutting attachment guardVibration damping system MufflerLocking nut Locking screwCutting equipment Cutting equipmentSharpening grass cutters and grass blades Sharpening the saw blade Trimmer headAssembling the handlebar and throttle RS44/RS52 AssemblyAssembling the handlebar and throttle GR41/GR50 Transport position, handlebarAssembling the cutting equipment Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade Fitting the trimmer guard Fitting other guards and cutting attachmentsTrimmer head Trimmy SII Adjusting the harness and clearing saw Standard harnessVector harness Correct balance Fuel safety Fuel HandlingFuel Fuelling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineStarting StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburettorHigh speed jet H GR41, GR50, RS44 Fine adjustment of the idle speed TCorrectly adjusted carburettor High speed jet H RS52Cooling system Cleaning the air filterMuffler Air filterBevel gear Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical data RS44 RS52 Engine EC-declaration of conformity Applies to Europe only Poly Trim Trimmy SII Page Auto ´z+Rq,¶60¨ Page 1150811-26 ´z+Rq,¶60¨ ´z+Rq,¶60¨

GR50, GR41, RS44, RS52 specifications

Husqvarna is renowned for its commitment to quality and performance in outdoor power equipment, and its range of robotic mowers epitomizes this standard. Among the standout models are the Husqvarna GR41, RS52, RS44, and GR50. Each of these mowers comes packed with features that cater to a variety of mowing needs, ensuring efficient lawn maintenance while allowing users to enjoy more free time.

The Husqvarna GR41 is designed for smaller lawns of up to 600 square meters. Its compact size and smart navigation technology enable it to maneuver efficiently around tight spaces and complex garden layouts. One of its remarkable features is the intuitive smartphone app that allows users to schedule mowing times, adjust settings, and receive notifications. The GR41's robust blade system ensures a clean cut, promoting healthier grass growth.

Moving on to the RS52, this model is well-suited for medium-sized lawns up to 800 square meters. It features advanced terrain handling capabilities, allowing it to tackle slopes of up to 25 degrees. Its weather-resistant design ensures durability in varying conditions. Additionally, the RS52 employs GPS-assisted navigation, which maps the mowing area and optimizes its route for maximum efficiency. This model also offers customizable mowing schedules, further enhancing convenience for users.

The Husqvarna RS44 is a step up, accommodating larger areas of up to 1,200 square meters. Its enhanced battery life allows for longer mowing sessions, and it boasts a powerful motor that adapts to different grass conditions. The RS44 incorporates smart technology for automated charging, meaning it returns to its station independently when the battery runs low. Its robust build ensures it can handle more demanding mowing tasks without compromising performance.

Finally, the Husqvarna GR50 stands out for its capability to manage expansive areas of over 1,600 square meters. This model integrates advanced AI technology for efficient mowing operations, adapting its patterns based on lawn growth and weather conditions. The GR50 features a larger cutting deck for quicker mowing and boasts a noise reduction system for quieter operation. Its rugged design and superior intelligence make it an ideal choice for users with larger lawns seeking a hassle-free mowing experience.

Together, these models represent Husqvarna's dedication to innovation and reliability, providing users with state-of-the-art solutions for automated lawn care. Whether managing small or large spaces, Husqvarna's robotic mowers deliver outstanding performance and efficiency.
Top Page Image Contents