Husqvarna 324RX-Series manual Fitting a blade guard, grass blade and grass cutter

Page 17

ASSEMBLY

Fitting a blade guard, grass blade and grass cutter

G

F

E

D

A B

C

•Hook the blade guard/combination guard (A) onto the ﬁtting on the shaft and secure with the bolt.

CAUTION! Use the recommended blade guard. See the Technical data section.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D), support cup (E) and support ﬂange

(F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

Fitting the blade guard and saw blade

K

J

H

I

A

L

•Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown.

CAUTION! Use the recommended blade guard. See the Technical data section.

G

F

D

B

C

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support ﬂange (F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

•When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade.You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The

English – 17

Image 17

Contents 324RX-SERIES Symbols KEY to SymbolsContents Machine′s safety equipment Safety InstructionsStop switch Personal protective equipmentVibration damping system Cutting attachment guardQuick release MufﬂerLocking nut Cutting equipmentStop switch Sharpening the saw blade Cutting equipmentTrimmer head Sharpening grass cutters and grass bladesFuel safety General safety precautionsStarting Transport and storageGeneral working instructions Basic safety rulesAdjusting the harness and clearing saw Terms Basic working techniquesABC of clearing Brush cutting with a saw bladeGrass trimming with a trimmer head Grass clearing using a grass bladeCutting What is what on the clearing saw? What is WHAT?Fitting the handlebar AssemblyTransport position, handlebar Fitting blades and trimmer headsFitting the blade guard and saw blade Fitting a blade guard, grass blade and grass cutterFitting a trimmer guard and Superauto II 1 trimmer head Fitting other guards and cutting attachmentsStandard harness Adjusting the harness and clearing sawSpreading the load on your shoulders Correct heightFuel Fuel HandlingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping Warm engineFor throttle handles with a start throttle lock Carburettor MaintenanceMufﬂer Cooling systemAir ﬁlter Cleaning the air ﬁlterSharpening grass cutters and grass blades Oiling the air ﬁlterSharpening the saw blade Daily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceTechnical data Technical DataTechnical Data Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSuper Auto Super Auto II Page S35 25 m ´z+H9y¶5O¨ Page 1140258-95 ´z+H9y¶5O¨ ´z+H9y¶5O¨