Porter-Cable BS600, CTE300, T525 instruction manual Generator Quick Facts

Page 20

Generator Quick Facts

CALL 1-888-559-8550 TO FIND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES

ENGINE

Use clean, fresh gasoline with a minimum 87 octane rating. Do not add gasoline

GAS

during or immediately after use.

 

 

ENGINE

Refer to engine owner's manual for oil recommendations.

 

OIL

Most generators are equipped with a low-oil shutdown. If the oil is low or if the

 

Generator is not level, the engine will not start.

 

 

WATTAGE

Make wattage calculations before use. Refer to general operator's manual for further

instructions.

 

 

 

WIRING

Contact an electrician for any wiring instructions. If wiring into a house, a double-throw

transfer switch and a heavy duty cord set must be used.

 

 

 

 

Use a standard (12V) lawn and garden battery with a minimum of 45 A.H. or 210 CCA.

 

 

BATTERY

The voltage and frequency are regulated by the rpm’s of the engine. Do not adjust the

throttle or governor to achieve higher performance. This will only alter the factory Pre-

VOLT

set settings and damage anything connected to the generator.

REG.

 

 

 

 

Be sure a volt/amp surge protector is used when sensitive electronic equipment is

 

used, such as: televisions, computers, stereos, and etc… The damage of such

 

equipment without the use of a protector WILL NOT be covered under warranty.

ENGINE

Do not adjust or attempt maintenance without consulting engine manual or an

authorized engine service center.

 

Add stabilizer to fuel tank and run engine for 5 minutes before storage.

STORAGE

When in long term storage, operate the generator every 60 days for at least 10 minutes

with a load on it. This will prevent the loss of residual magnetism that produces the

 

 

electricity.

 

Allow the generator to run 5 minutes at no load for the engine and the genhead to

 

stabilize.

OPERATION

Make sure the adequate size of extension cord is used. Refer to the Grounding

 

Instructions/Extension Cord section of the owners manual.

 

If the generator is operating equipment that is drawing half of the rated watts it is

 

considered 50% load. Using all of the rated watts is considered 100% load.

 

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

 

 

 

Porter-Cable Corporation

 

4825 Highway 45 North

 

P.O. Box 2468

 

Jackson, TN 38302-2468

 

1-888-559-8550

20 — ENG

Page 19 Page 20
Image 20
Page 19 Page 20
Contents Instruction Manual Generators Specification ModelWarranty This Warranty is not Transferable and does not CoverSafety Guidelines Definitions Important Safety InstructionsHazard What could Happen HOW to Prevent IT Risk of Electrocution and FireOperation of generator in rain Wet, icy, or flooded conditionsRisk of Fire Or wall. do not Operate UnitIndoors or in ANY Confined AreaRisk of Breathing Inhalation Hazard Your generator Risk of Unsafe OperationUse a U.L. listed voltage surge Risk from Lifting Risk of HOT SurfacesRisk of Moving Parts Assembly Typical Installation of Battery BS600 & BSV800Remove Generator from Carton Grounding the GeneratorExtension Cord Wire Gauge Chart Length Obtaining Electricity from the GeneratorFor BSV800 AmperageOperation Connecting Electrical Loads Stopping EngineMaintenance Engine MaintenanceGenerator Maintenance Customer Responsibilities TableStorage Engine PreparationExample Wattage CalculationsRunning Watts Starting Watts 12V DC Battery Charger RunStart Hand DrillHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide Engine will not startNo electrical output Repeated circuit breaker trippingGenerator Quick Facts

BS600, T525, CTE300 specifications

Porter-Cable has long been recognized in the power tool industry for its commitment to quality and innovation. Among its impressive lineup, the T525, CTE300, and BS600 tools stand out for their performance and versatility. Each model boasts distinct features and technologies designed to cater to the needs of both professionals and DIY enthusiasts.

The Porter-Cable T525 is a powerful corded electric tool primarily designed for sanding tasks. With a robust motor, it delivers consistent performance and excellent material removal capabilities. One of its standout features is the integrated dust collection system, which significantly reduces mess and improves visibility during use. The T525 also offers variable speed control, enabling users to adjust the sanding speed according to the task at hand. With an ergonomic grip and lightweight design, it minimizes user fatigue, making it suitable for extended use.

The CTE300 is a versatile tool that excels in both cutting and shaping materials. It features a high-torque motor that ensures efficient operation, whether for woodworking or other materials. The CTE300 comes with adjustable depth settings, enabling precise cuts and enhancing accuracy. Another key characteristic is its blade compatibility, allowing users to switch between different types of blades depending on their project requirements. The tool's balanced design contributes to better handling and reduces strain on the user, making it a favorite among carpenters and contractors.

Finally, the Porter-Cable BS600 is a reliable bandsaw that offers exceptional cutting capabilities. Its powerful motor drives a premium blade that can easily handle various materials, from wood to metal. The BS600 features an adjustable table that supports bevel cuts, providing added flexibility for intricate projects. A highlight of this model is its built-in safety features, including blade guards and an emergency shut-off switch, which enhance user protection. The lightweight frame and compact design allow for easy transport, making it an ideal choice for both workshop and job site environments.

In summary, the Porter-Cable T525, CTE300, and BS600 represent the brand's dedication to delivering high-quality tools equipped with advanced technologies. Their individual features cater to a wide range of applications, ensuring that users can achieve professional results with ease and efficiency. Whether it’s sanding, cutting, or shaping, these tools are designed to meet the demands of modern woodworking and construction projects.
Top Page Image Contents