Poulan 191663 Transaxle Motion Control LE- VER Neutral Adjustment, Front Wheel TOE-IN/CAMBER

Page 25

Engine Pulley

Clutching Idler

Stationary Idler

Center Span

Keeper

Transmission

Input Pulley

01510

TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.

Loosen adjustment bolt in front of the

 

right rear wheel, and lightly tighten.

2.

Start engine and move motion con-

 

trol lever until tractor does not move

 

forward or backward.

3.

Hold motion control lever in that posi-

 

tion and turn engine off.

4.

While holding motion control lever in

 

place, loosen the adjustment bolt.

5.

Move motion control lever to the neu-

 

tral (N) (lock gate) position.

6.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed

to get to adjustment bolt, move mower

deck height to the lowest position.

After above adjustment is made, if the

tractor still creeps forward or backward

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact our authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from an authorized ser- vice center/department. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

while motion control lever is in neutral

position, follow these steps:

1.

Loosen the adjustment bolt.

2.

Move the motion control lever 1/4 to

 

1/2 inch in the direction it is trying to

Axle

Cover

Square Key

00663

 

creep.

3.

Tighten adjustment bolt securely.

4.

Start engine and test.

5.

If tractor still creeps, repeat above

 

steps until satisfied.

Motion Control

Neutral

Lever

Lock Gate

 

Adjustment

02239

Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before op- erating the tractor. See “PURGE TRANS- MISSION” in the Operation section of this manual.

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT- TERY

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model NO. CO18H42STA Warranty Table of ContentsGeneral Operation Safety RulesII. Slope Operation III. Children IV. ServiceDo not Safety Rules Customer Responsibilities Product SpecificationsAPI-SF-SJ Steering Wheel Unassembled PartsASSEMBLY/PRE-OPERATION Check Battery Install Mulcher PlateCheck Tire Pressure To Convert to Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate MowerTo Transport To Start Engine Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mulching Mowing Tips Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Transaxle Cooling EngineTransaxle Pump Fluid BeltsCleaning To Install Mower Service and AdjustmentsTo Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingBelt Installation To Replace Mower Blade Drive BeltTo Adjust Brake To Check and Adjust BrakeTo Check Brake To Replace Motion Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control LE- VER Neutral AdjustmentTransmission Removal Replacement Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable Replacing BatteryTo Adjust Carburetor To Replace Headlight BulbStorage BatteryOther Problem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

191663 specifications

The Poulan 191663 is a remarkable piece of equipment tailored for outdoor enthusiasts and professionals alike. As a part of Poulan's extensive lineup, it exemplifies durability, performance, and user-friendliness, making it an excellent choice for those tackling various landscaping and yard maintenance tasks.

One of the standout features of the Poulan 191663 is its powerful engine. Equipped with a reliable 42cc, 2-cycle gas engine, the chainsaw delivers exceptional cutting performance while maintaining a lightweight design. This engine ensures that users can tackle even the toughest jobs with ease, whether it’s felling trees or trimming branches.

The design of the Poulan 191663 emphasizes user comfort and control. It comes with an ergonomic handle that provides a secure grip, allowing for extended use without causing undue fatigue. Coupled with its lightweight construction, this chainsaw minimizes strain, making it ideal for both experienced users and novices.

Safety features are paramount with the Poulan 191663. The chainsaw is equipped with an automatic oiler, which ensures that the chain receives the lubrication it needs for optimal performance while reducing wear. Additionally, a safety chain brake is included, providing an added layer of protection against kickback, which is essential for maintaining safety during operation.

Another notable technology featured in the Poulan 191663 is its easy-start system. This user-friendly technology allows for hassle-free starting with minimal effort, making it accessible for users who may struggle with traditional chainsaw ignition systems. The quick-access air filter ensures that maintenance is straightforward, allowing for easy cleaning and replacement, thus prolonging the chainsaw's lifespan.

Moreover, the Poulan 191663 boasts a 16-inch bar and chain, providing ample cutting capacity for a range of applications. Its versatile design allows users to efficiently navigate both small and medium-sized trees and branches, making it an indispensable tool for homeowners and landscape professionals alike.

In summary, the Poulan 191663 combines power, safety, and ease of use into one compact package. With its robust engine, ergonomic design, and essential safety features, this chainsaw is a reliable choice for anyone looking to enhance their outdoor maintenance capabilities. Whether you're pruning your garden, clearing storm debris, or tackling larger cutting jobs, the Poulan 191663 is a dependable partner for all your cutting needs.
Top Page Image Contents