Poulan 194613 manual Reverse Operation System ROS, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Depress clutch/brake pedal all the way down and hold.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 6

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PD17542LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

194613 specifications

The Poulan 194613 is a versatile and powerful chainsaw designed for both professional loggers and casual users looking to tackle home landscaping projects. Known for its robust performance and user-friendly features, it stands out as an excellent tool for a variety of cutting tasks.

One of the main features of the Poulan 194613 is its potent engine. It is equipped with a reliable 2-cycle gas engine that delivers ample power to handle demanding cutting applications. The engine is designed for efficiency, allowing users to complete tasks more quickly without sacrificing performance. This makes the chainsaw suitable for felling trees, trimming branches, and cutting firewood.

Additionally, the Poulan 194613 features an easy-to-start system. This technology minimizes the effort required to start the chainsaw, ensuring that users can get to work with minimal frustration. Coupled with the tool’s lightweight design, it enhances maneuverability and reduces fatigue during extended use, making it an inviting option for users at all skill levels.

Safety is another priority in the design of the Poulan 194613. It comes equipped with features such as a chain brake, which stops the chain quickly in cases of kickback, providing peace of mind while operating. The rear handle is ergonomically designed with a comfortable grip, allowing for better control and stability during operation.

Moreover, the Poulan 194613 is equipped with a robust bar and chain system that ensures smooth cutting through various types of wood. The chain is designed for durability, maintaining sharpness for longer periods and requiring less frequent replacements. This translates to less downtime and increased productivity, particularly beneficial for professionals who rely on their tools daily.

Another noteworthy characteristic of the Poulan 194613 is its tool-less chain tensioning system. This feature allows users to easily adjust the chain tension without the need for additional tools, simplifying the maintenance process and ensuring optimal performance at all times.

With its powerful engine, numerous safety features, and user-friendly technologies, the Poulan 194613 is an ideal choice for anyone looking to invest in a reliable chainsaw that can handle a wide range of cutting tasks. Whether for professional use or home improvement projects, this chainsaw provides a combination of performance and convenience that meets the needs of diverse users.
Top Page Image Contents