Poulan 196692 manual Troubleshooting Points

Page 25

TROUBLESHOOTING POINTS

PROBLEM

 

CAUSE

 

CORRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

Will not start

 

1.

Out of fuel.

 

1.

Fill fuel tank.

 

 

 

 

2.

Engine not “CHOKED” properly.

 

2.

See “TO START ENGINE” in Operation section.

 

 

 

 

3.

Engine flooded.

 

3.

Wait several minutes before attempting to start.

 

 

 

 

4.

Bad spark plug.

 

4.

Replace spark plug.

 

 

 

 

5.

Dirty air filter.

 

5.

Clean/replace air filter.

 

 

 

 

6.

Dirty fuel filter.

 

6.

Replace fuel filter.

 

 

 

 

7.

Water in fuel.

 

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

 

8.

Loose or damaged wiring.

 

8.

Check all wiring.

 

 

 

 

9.

Carburetor out of adjustment.

 

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

10.

Engine valves out of adjustment.

 

10.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Hard to start

 

1.

Dirty air filter.

 

1.

Clean/replace air filter.

 

 

 

 

2.

Bad spark plug.

 

2.

Replace spark plug.

 

 

 

 

3.

Weak or dead battery.

 

3.

Recharge or replace battery.

 

 

 

 

4.

Dirty fuel filter.

 

4.

Replace fuel filter.

 

 

 

 

5.

Stale or dirty fuel.

 

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

 

6.

Loose or damaged wiring.

 

6.

Check all wiring.

 

 

 

 

7.

Carburetor out of adjustment.

 

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

8.

Engine valves out of adjustment.

 

8.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Engine will not turn over

 

1.

Brake pedal not depressed.

 

1.

Depress brake pedal.

 

 

 

 

2.

Attachment clutch is engaged.

 

2.

Disengage attachment clutch.

 

 

 

 

3.

Weak or dead battery.

 

3.

Recharge or replace battery.

 

 

 

 

4.

Blown fuse.

 

4.

Replace fuse.

 

 

 

 

5.

Corroded battery terminals.

 

5.

Clean battery terminals.

 

 

 

 

6.

Loose or damaged wiring.

 

6.

Check all wiring.

 

 

 

 

7.

Faulty ignition switch.

 

7.

Check/replace ignition switch.

 

 

 

 

8.

Faulty solenoid or starter.

 

8.

Check/replace solenoid or starter.

 

 

 

 

9.

Faulty operator presence switch(es).

 

9.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Engine clicks but will not

 

1.

Weak or dead battery.

 

1.

Recharge or replace battery.

 

start

 

2.

Corroded battery terminals.

 

2.

Clean battery terminals.

 

 

 

 

3.

Loose or damaged wiring.

 

3.

Check all wiring.

 

 

 

 

4.

Faulty solenoid or starter.

 

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

 

 

 

 

Loss of power

 

1.

Cutting too much grass/too fast.

 

1.

Raise cutting height/reduce speed.

 

 

 

 

2.

Throttle in “CHOKE” position.

 

2.

Adjust throttle control.

 

 

 

 

3.

Build-up of grass, leaves and trash under mower.

 

3.

Clean underside of mower housing.

 

 

 

 

4.

Dirty air filter.

 

4.

Clean/replace air filter.

 

 

 

 

5.

Low oil level/dirty oil.

 

5.

Check oil level/change oil.

 

 

 

 

6.

Faulty spark plug.

 

6.

Clean and regap or change spark plug.

 

 

 

 

7.

Dirty fuel filter.

 

7.

Replace fuel filter.

 

 

 

 

8.

Stale or dirty fuel.

 

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

 

9.

Water in fuel.

 

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

 

10.

Spark plug wire loose.

 

10.

Connect and tighten spark plug wire.

 

 

 

 

11.

Dirty engine air screen/fins.

 

11.

Clean engine air screen/fins.

 

 

 

 

12.

Dirty/clogged muffler.

 

12.

Clean/replace muffler.

 

 

 

 

13.

Loose or damaged wiring.

 

13.

Check all wiring.

 

 

 

 

14.

Carburetor out of adjustment.

 

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

15.

Engine valves out of adjustment.

 

15.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Excessive vibration

 

1.

Worn, bent or loose blade.

 

1.

Replace blade. Tighten blade bolt.

 

 

 

 

2.

Bent blade mandrel.

 

2.

Replace blade mandrel.

 

 

 

 

3.

Loose/damaged part(s).

 

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation XT24H42YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

196692 specifications

The Poulan 196692 is a versatile and powerful chainsaw designed for both professional and home use. With a robust set of features, this chainsaw combines efficiency, durability, and ease of use, making it a popular choice among tree care professionals and DIY enthusiasts alike.

One of the standout features of the Poulan 196692 is its potent 50cc engine. This engine provides ample power for cutting through thick branches and logs, delivering reliable performance under demanding conditions. The chainsaw also boasts a 20-inch bar, which allows for a large cutting capacity, enabling users to tackle various outdoor tasks seamlessly, from limb trimming to tree felling.

In terms of technology, the Poulan 196692 incorporates advanced anti-vibration technology. This feature significantly reduces the amount of vibration transferred to the user, making it more comfortable to operate for extended periods. This is particularly beneficial for those who find themselves engaged in heavy cutting tasks, as it minimizes fatigue and helps maintain precision.

Another important characteristic of the Poulan 196692 is its easy starting system. The chainsaw is equipped with a spring-assist starter, ensuring that users can start the machine with minimal effort. This technology is especially useful for those who may struggle with traditional pull-start systems, as it enhances the overall user experience.

Safety is also a paramount consideration in the design of the Poulan 196692. The chainsaw features a chain brake system that can be activated quickly in the event of kickback, providing an extra layer of protection for the operator. Additionally, it includes a low-kickback chain, which is engineered to reduce the risk of kickback accidents, making it a safer option for those new to using chainsaws.

The Poulan 196692 also emphasizes ease of maintenance. The tool-less chain tensioning system allows users to adjust the chain tension without needing additional tools, streamlining the maintenance process and ensuring optimal performance. The air filter is easily accessible, promoting regular cleaning and upkeep, which contributes to the longevity of the chainsaw.

In conclusion, the Poulan 196692 emerges as a formidable chainsaw that blends power, safety, and user-friendly features. Its strong engine, anti-vibration technology, easy starting system, and safety enhancements make it an excellent choice for anyone looking to invest in a reliable and efficient chainsaw for their outdoor tasks. Whether trimming large branches or cutting firewood, the Poulan 196692 is designed to meet the demands of a variety of cutting jobs.
Top Page Image Contents