Poulan 195021 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

9/16" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove locknut and large flat washer from steering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

•Slide the steering sleeve over the steering shaft.

•Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

•Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING WHEEL

INSERT

LOCK NUT

LARGE FLAT WASHER

STEERING WHEEL

STEERING WHEEL ADAP- TOR

STEERING

SHAFT

STEERING

SLEEVE

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents DB24H42YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Assemble Gauge Wheels to Mower Deck See FigCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195021 specifications

The Poulan 195021 is a versatile and powerful chainsaw designed for both homeowners and professionals seeking reliability and performance for various cutting tasks. Known for its robust build and user-friendly features, the Poulan 195021 is an excellent choice for those who value efficiency and ease of use.

One of the standout features of the Poulan 195021 is its powerful 20-inch bar and chain, which allows for effective cutting of both small and medium-sized trees, as well as trimming and pruning branches. The 51cc engine provides ample power, making quick work of tough jobs while maintaining a manageable weight for easy handling.

The chainsaw is equipped with a centrifugal air cleaning system that significantly reduces the amount of debris and dust entering the engine. This feature extends the lifespan of the chainsaw by minimizing wear and tear on critical components, ensuring that it operates at peak efficiency over time. The innovative design of the air filter makes it easy for users to maintain and replace when necessary.

Safety is a priority with the Poulan 195021, which includes several crucial safety features. The automatic chain lubrication system keeps the chain fully lubricated during operation, reducing friction and wear while maintaining optimal performance. Additionally, the chainsaw comes with a chain brake that offers an additional layer of protection by stopping the chain instantly in case of kickback.

User comfort is also a crucial aspect of the Poulan 195021's design. It features an ergonomic handle that allows for a secure and comfortable grip, reducing fatigue during extended use. The anti-vibration technology integrated into the chainsaw absorbs the vibrations generated during operation, further enhancing user comfort and promoting better control.

Overall, the Poulan 195021 stands out in the competitive chainsaw market due to its blend of power, safety, and user-friendly features. Whether you are a seasoned professional or a homeowner tackling weekend projects, the Poulan 195021 offers a reliable and efficient solution for your cutting needs. With its robust performance and thoughtful design, it is well-suited for various applications, making it a valuable addition to any toolkit.
Top Page Image Contents