Poulan 96042010701, 431535 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 11

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 10)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 10

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 11)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE:Adjustgaugewheelswithtractoronaflatlevelsurface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, washer, washer, and locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

Fig. 11

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USINGTHEREVERSEOPERATIONSYSTEM(SeeFig.12) Only use if you are certain no children or other bystanders will enter the mowing area.

•Move motion control lever to neutral position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before and while backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

Fig. 12

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES -

•Disengage attachment clutch control.

CAUTION: Donotoperatethemowerwithout either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 13).

S

11

Fig. 13

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model PB195H42LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Brake System To Adjust Seat See FigCheck Tire Pressure Check Deck LevelnessOperation Position Know Your TractorROS on To USE Throttle Control See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Reverse Operation System ROSCheck Engine OIL Level Before Starting the EngineTo Operate on Hills Towing Carts and Other AttachmentsAutomatic Transmission Warm UP Mowing TipsPurge Transmission Schedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Engine Spark Plugs CleaningEngine Cooling System See Fig MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Install belt on engine pulley M Turn nut right Turn nut left To raise mower To lower mower To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentTransmission Engine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingTroubleshooting Points Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXStevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactGarantie cette de exclus sont normal l’entretien et Dept Service Customer Products OutdoorCanada Au AutoriséDegrés Correction Cause Problème Dépannage DE GuidePuissance de Entreposage Calandrelaetcapotleenleverpour Réglages ET RévisionMoteur Carburateur LE Régler PourTionrec Rossage -AVANT/CAR Roues DES ConvergenceDI LA DE L’ALIGNEMENT Régler Pour Freins LES Vérifier Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourTondeuse DE Lame DE Mentnetraî ’EN Courroie LA Remplacer Pour30 .Fig Tondeuse LA Niveau LE Ajuster Pour32 .Fig 31 .Fig25 .Fig 28 .Fig27 .Fig 26 .FigTondeuse LA Enlever Pour Cour LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Roie Fig VoirFig la Voir Ventilation DE Système Ligne EN Installé D’ESSENCE FiltreMontage ’ALLUMAGE BougieSionmistrans LA DE Moteur Fluide Entretien’AIR Tamis LE Nettoyer AIR À FiltreFrein DU Fonctionnement Fig la Voir Lame LA EnleverLames DES Entretien PneusLubrification DE Tableau Utilisation Chaque Avant15 .Fig UtilisationTransmission LA Purger Tonte DE ConseilsTracteur LE Transporter Pour Accessoires Autres ET Charrettes DES Remorquer PourMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirROS Arrière CHE -MAR EN Fonctionnement DE Système Jauge DE Roues LES Régler PourTondeuse DE Lames LES Arrêter Pour Fig la Voir Arrêter Pour 6 .Fig GAZ DES Commande LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Reculer Pour ET Avancer Pour’OPÉRA DE Présence DE Système DU Commutateur Propriété la de lendommagement Niveau DE EST Tondeuse LA SI Vérifier Frein DE Système LE VérifierPlace EN Correctement Carton LE Deballer Et 3 .Figs les Voir Siège LE AjustezFig la Voir Batterie LA Vérifier Palette DE Tracteur LE Retirer AvantSiège Montar SIN PiezasSommaire En l’utilisation pour Conseils Sécurité DE RèglesTracteurs des sécurité toute EnfantsGénéral Fonctionnement AvertissementTracteurs des sécurité toute en l’utilisation pour Conseils Pentes LES Dans FonctionnementPelouse DE Tracteur PB195H42LT Modèle Propriétaire DU Manuel
Top Page Image Contents