Poulan 404172 manual To USE Cruise Control -J See Fig, To Adjust Mower Cutting Height See Fig

Page 12

OPERATION

J

K

L

FIG. 17

TO USE CRUISE CONTROL -J (See Fig. 17)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 7)

The position of the attachment lift lever (A) determines the cutting height.

T

FIG. 18

Put attachment lift lever in desired cutting height slot.

Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

• The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

12

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the fi rst cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 19)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a fl at level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.19

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

Image 12
Contents PB22H54YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonInstall Mower and Drive Belt Assemble Front Wheel to Mower See FigFirst Install ANTI-SWAY BAR S Check Tire Pressure Check Deck Levelness Check for Proper Position of ALL BeltsCheck Brake System Operation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To USE Cruise Control -J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install MowerTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Parts and Service