Poulan DPR22H48STB To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 14

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IF YOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

ATTACHMENT CLUTCH

ATTACHMENT

SWITCH PULL OUT TO

LIFT LEVER

"ENGAGE"

HIGH

 

POSITION

 

LOW

 

POSITION

PUSH IN TO

 

"DISENGAGE"

 

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

FIG. 11

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

FIG. 10

14

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents DPR22H48STB Safety Rules Safe Operation Practices for Ride-On MowersSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigPurge Transmission Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Spark Plugs CleaningMuffler Engine OIL FilterTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Service Notes Schematic Tractor Model Number DPR22H48STBElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Engine Optional EquipmentSeat Assembly Decals Wheels & TiresMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

DPR22H48STB specifications

The Poulan DPR22H48STB is a robust riding mower designed to tackle the diverse mowing needs of homeowners with larger lawns. With its exceptional performance and user-friendly features, it stands out in the market for those seeking efficiency and reliability.

At the heart of the DPR22H48STB is a reliable 22 HP Briggs & Stratton engine, known for its power and durability. This engine provides the necessary strength to handle tall grass and uneven terrain, making mowing a seamless task. Coupled with an easy-start system, users can quickly get the mower running without the hassle often associated with pull-start engines.

The mower features a 48-inch cutting deck, which is perfect for navigating tighter areas while still covering a significant amount of ground with each pass. The cutting height can be easily adjusted to six different positions, allowing users to customize their cut based on the grass type and weather conditions. This flexibility ensures that every user can maintain their yard with precision and care.

One of the standout features of the Poulan DPR22H48STB is its hydrostatic transmission, which provides smooth and effortless motion. This technology allows for seamless speed adjustments without the need for gear shifting, making it easier to maneuver around obstacles and maintain control on inclines. As a result, users experience less fatigue during longer mowing sessions.

Durability is another key characteristic of this model. The steel deck construction ensures that the mower withstands the elements and heavy use without compromising performance. Additionally, the mower’s wide rear tires enhance traction and stability, making it an ideal choice for uneven surfaces.

Further enhancing the mowing experience is the comfortable, adjustable seat, which allows users to find their ideal position for extended periods of use. The steering wheel is ergonomically designed, ensuring ease of use even in tight turns or challenging terrains.

In summary, the Poulan DPR22H48STB combines power, efficiency, and comfort. It is equipped with a potent Briggs & Stratton engine, a versatile cutting deck, and an innovative hydrostatic transmission, making it a reliable choice for homeowners looking to maintain their lawn effortlessly. With its solid build and thoughtful features, this riding mower simplifies yard care, allowing users to enjoy their outdoor spaces to the fullest.
Top Page Image Contents