Poulan DB27H48YT manual To Replace Motion Drive Belt See Fig, Belt Removal, Belt Installation

Page 24

SERVICE AND ADJUSTMENTS

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 25

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from engine pulley and around electric clutch.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

•Install belt through stationary idler and clutching idler.

•Reinstall clutch locator and tighten nut securely.

•Reconnect clutch harness.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSMISSION

CLUTCH

INPUT PULLEY

WIRE

 

HARNESS

FIG. 26

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents DB27H48YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Mower and Drive Belt See Figs To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

DB27H48YT specifications

The Poulan DB27H48YT is a robust, high-performance lawn tractor that stands out in the market for home gardening and yard maintenance. Known for its versatility and reliability, this model is particularly aimed at homeowners with medium to large yards, offering an excellent balance between power and user-friendliness.

One of the main features of the Poulan DB27H48YT is its powerful 27 HP Briggs & Stratton engine, which ensures optimal performance for various mowing tasks. The engine is designed with improved efficiency and durability in mind, providing homeowners with a dependable solution for their lawn care needs. The automatic transmission enhances ease of use, allowing operators to shift gears seamlessly without the hassle of manual clutching.

The 48-inch cutting deck is another noteworthy characteristic, featuring five adjustable cutting heights that range from 1.5 to 4 inches. This flexibility allows users to customize their mowing experience based on grass conditions and personal preferences, ensuring an even and precise cut across different types of terrain. The deck is constructed from high-quality material, designed to withstand the rigors of regular use and provide a long-lasting lifespan.

Incorporating advanced mowing technologies, the Poulan DB27H48YT is equipped with a debris shield and a mulching kit option. These features not only enhance the mowing experience but also contribute to improved lawn health by returning nutrients back into the soil. Additionally, the tractor's side discharge chute allows for efficient grass clipping management.

User comfort is taken into consideration with a plush, adjustable seat and an ergonomic steering wheel, ensuring a comfortable ride even during extended mowing sessions. The easy-to-access control panel is designed for effortless operation, making it suitable for users of all skill levels.

Other characteristics of the Poulan DB27H48YT include rugged tires that provide excellent traction on various terrains and a convenient fuel gauge for monitoring gas levels. The model also boasts a sturdy frame and construction, ensuring stability and longevity, making it an investment worth considering for any homeowner looking to simplify lawn care.

Overall, the Poulan DB27H48YT combines power, advanced technology, and user-friendly features to deliver an exceptional lawn tractor that meets the demands of modern gardening.
Top Page Image Contents