Poulan PD20PH48STA owner manual To Level Mower Housing, To Replace Mower Drive Belt

Page 21

SERVICE AND ADJUSTMENTS

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

01553

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

02548

MANDREL

“B”“B”

FIG. 22

BOTH FRONT PLATE LINKS MUST BE EQUAL IN LENGTH

 

02516

 

TRUNNION

NUT “D”

 

FRONT PLATE

NUT “C”

02517

ASSEMBLY

 

FIG. 23

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 24)

•Park tractor on a level surface. Engage parking brake.

•Lower mower to its lowest position.

•Disengage belt tention rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PD20PH48STA Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsSeat Nose Roller MowerTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig To Replace Mower Drive Belt To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PD20PH48STA, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD20PH48STA, Product Number 954 56 KEY Part NO. NO. Description DriveSteering Assembly 180656 Wheel Steering Engine Stem Tank Fuel Seat Assembly Wheels & Tires DecalsMower Lift KEY Part NO. NO. Description Mower Deck 175820 Pulley Idler Flat Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service
Top Page Image Contents