Poulan PB19H42YT manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig.30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

 

A

 

Negative

C

(Black)

Cable

 

B

Positive (Red) Cable

03037

FIG. 30

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

03075

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Image 23
Contents PB19H42YT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig StoppingTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Transport See Figs Before Starting the EngineReverse Operation System ROS To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Schedule MaintenanceMaintenance General RecommendationsTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsSlide mower out from under right side of tractor To Install Mower See FigsTo Level Mower To Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig To Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Limited Warranty Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Parts and Service