Poulan PB195H42LT warranty To Level Mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 29)

With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

Fig. 29

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 30)

With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to its highest position.

At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 30

If adjustment is necessary, see step in Visual Adjust- ment instructions above.

Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 31 & 32) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to highest position.

Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 31

If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (tighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 32

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Image 20
Contents PB195H42LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersSafe Handling of Gasoline General ServiceIII. Children Table of Contents Unassembled Parts SteeringAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidTo Adjust Seat See Fig Check Tire PressureCheck Deck Levelness Check for Proper Position of BeltsOperation Position Know Your TractorROS on HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate MowerBefore Starting the Engine To Operate on HillsTowing Carts and Other Attachments Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Removal See Fig BeltsEngine Cleaning Muffler IN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty
Related manuals
Manual 64 pages 32.59 Kb Manual 20 pages 49.99 Kb