Poulan PD18H42STA Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

CENTER SPAN KEEPER

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PD18H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Gauge WheelTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See a Check Battery See FigCheck Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips General Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Interlocks and Relays Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbAcceleration Test To Adjust Throttle Control Cable See FigTo Adjust Carburetor See Fig Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PD18H42STA, Product no 56 SchematicTractor - Model Number PD18H42STA, Product no 56 Electrical KEY Part NO. NO. Description 159 KEY Part Description Tractor - Model Number PD18H42STA, Product no 56 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PD18H42STA, Product no 56 Engine KEY Part NO. NO. Description KEY Part Description Wheels & Tires Tractor - Model Number PD18H42STA, Product no 56 DecalsTractor - Model Number PD18H42STA, Product no 56 Mower Lift Repair Parts 152 153 154 Tractor - Model Number PD18H42STA, Product no 56 Mower Deck182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PD18H42STA specifications

The Poulan PD18H42STA is a powerful and versatile lawn tractor designed to make mowing easier and more efficient for homeowners and landscapers alike. With its robust build and a range of user-friendly features, the PD18H42STA is ideal for managing medium to large lawns.

One of the standout features of the Poulan PD18H42STA is its 18 horsepower Briggs & Stratton engine, known for efficiency and reliability. The engine provides ample power for cutting and handling various terrain types. Its overhead valve design enhances fuel efficiency and reduces emissions, aligning with modern environmental standards.

The PD18H42STA comes equipped with a 42-inch cutting deck, allowing for a wider cutting path, which means fewer passes over your lawn. The adjustable cutting height feature enables users to select from six different positions, ranging from 1.5 inches to 4 inches, accommodating different grass types and seasonal requirements. This flexibility ensures a clean and even cut, promoting healthy grass growth.

Another notable technology in this tractor is the hydrostatic transmission. This system allows for smooth acceleration and deceleration, providing easy maneuverability, especially in tight spaces. The absence of shifting gears simplifies operation, making it accessible even for those who may not be familiar with riding mowers.

Comfort is paramount in the design of the PD18H42STA. The seat is ergonomically designed with ample cushioning to provide comfort during extended use. The easy-to-use steering wheel allows for precise control, while the foot pedal allows for easy speed adjustments.

Maintenance is straightforward with the Poulan PD18H42STA. The deck wash feature makes it easy to clean the underside of the cutting deck, helping to prevent grass buildup and ensuring optimal performance. Additionally, a removable fuel tank cap facilitates refueling without spills, enhancing convenience.

In summary, the Poulan PD18H42STA combines power, comfort, and technology to deliver an excellent mowing experience. With its reliable engine, efficient cutting deck, and user-friendly features, it stands out as a capable choice for anyone looking to maintain a beautiful lawn with less effort.
Top Page Image Contents