Poulan 96042003600 manual Tools Required for Assembly, To Remove Tractor from, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

INSERT

5/16 HEX BOLT

A socket wrench set will make assembly easier. Standard

wrench sizes are listed.

5/16 LOCK WASHER

(1) 1/2" wrench Utility knife

LARGE FLAT WASHER

 

(2)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means

 

 

when you are in the operating position (seated behind the

 

 

steering wheel).

 

STEERING

 

 

WHEEL

TO REMOVE TRACTOR FROM

STEERING BOOT

 

CARTON

ADAPTER

 

UNPACK CARTON

 

 

• Remove all accessible loose parts and parts cartons

TABS

 

from carton.

TAB

 

• Cut along dashed lines on all four panels of carton.

 

SLOTS

Remove end panels and lay side panels flat.

 

 

• Check for any additional loose parts or cartons and

EXTENSION SHAFT

 

remove.

 

 

 

LOWER STEERING SHAFT

 

BEFORE REMOVING TRACTOR FROM

 

 

SKID

 

03125

ATTACH STEERING WHEEL (See Fig. 1)

FIG. 1

 

ASSEMBLE EXTENSION SHAFT AND BOOT

 

 

• Slide extension shaft onto lower steering shaft.

INSTALL SEAT (See Figs. 2 and 3)

 

• Place tabs of steering boot over tab slots in dash and

 

push down to secure.

• Remove bolt and flat washer securing seat to cardboard

 

packing and set aside for assembly of seat to tractor.

INSTALL STEERING WHEEL

Remove the cardboard packing and discard.

• Position front wheels of the tractor so they are pointing

• Connect switch to seat.

straight forward.

• Place seat on seat pan so all three (3) bottom pads

• Remove steering wheel adapter from steering wheel

are positioned over large slotted holes in pan.

and slide adapter onto steering shaft extension.

 

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB195H42LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Carton Tools Required for AssemblyTo Remove Tractor from Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemReverse Operation System ROS To Operate Mower See FigTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Transport Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningSchedule MaintenanceGeneral Recommendations Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemBelts BatteryEngine Transaxle CoolingCleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G Precision SIDE-TO-SIDE Adjustment To Level MowerTo Replace Motion Belt Drive See Fig Belt InstallationTo Replace Mower Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeService Notes Service Notes Page Page Dentretien Remarques Dentretien Remarques Degrés Suivant LES UNE Pliez EST CeciLimitée Garantie Dépannage DE Guide Défectueux estRalenti DU Commande LA Régler Pour GAZ DES CommandeEntreposage Réglages ET Révision Tionrecdi CarrossageAVANT/ Roues DES Convergence LA DE L’ALIGNEMENT Régler PourFreins LES Vérifier Pour Courroie Acer Rempl Pour’ENTRAÎNEMENT 25 .FIG21 .FIG Tondeuse LA Niveau LE Ajuster Pour23 .FIG 22 .FIG19 .FIG 17 .FIG 18 .FIG16 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision Tondeuse LA Enlever Pour’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTransmission LA DE Refroidissement LubrificationTrapézoïdales Courroies Fig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET O I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Tonte DE Conseils UtilisationTransmission LA Purger Queti’ESSENCE Réservoir LE Remplir Accessoires AutresMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierROS Arrière CHE MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour Tondeuse DE Lames LES Arrêter PourFig la Voir Mentne GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Tionsta DE Frein LE Engager PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Et 2 .Figs les Voir Siège LE Ajustez DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas CCA .MIN AMP/HR U1R DimensionSommaire SL-SG-API’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé
Top Page Image Contents