Poulan 419055 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Figs

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Remove mower belt from engine pulley (M).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Figs. 20-24)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position.

CAUTION: After rear lift links are dis- connected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

• Slide mower out from under right side of tractor.

B

 

Q R

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

MF

AE

P

K

C

D

L

FIG. 19

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model PB19542LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See Figs a and 2BCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Engine HOW to USE Your TractorMower Blades Ground DriveReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigTo Operate Mower See Fig Before Starting the Engine To Start Engine See Fig Mowing TipsGeneral Recommendations MaintenanceBlade Removal See Fig TractorCheck Operator Presence System Check Reverse Operation ROS SYS- TEMEngine Muffler Clean AIR ScreenAIR Filter Engine OIL FilterTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Belt Drive See Fig Front Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentInterlocks and Relays To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbCylinders StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXHOP Limited WarrantyLimitée Garantie UNE Pliez EST Ceci Degrés Suivant LES’ENTRETIEN Remarques Défectueux est Dépannage DE GuideRalenti Entreposage DES L’AMPOULE Remplacer Pour GAZ DES CommandeRéglages ET Révision Fig la Voir Calandre LA ET Capot LE Enlever Pour31 .Fig Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourCarrossage AVANT/ Roues DES Convergence’EN Courroie LA Remplacer Pour FIG LA Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourFIG LA Voir Tondeuse DE Lame DE Mentnetraî27 .FIG Tondeuse LA Niveau LE Ajuster Pour28 .FIG 26 .FIG21 .FIG 24 .FIG23 .FIG 22 .FIGTondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerReglages ET Revision Fig VoirEntretien Bornes LES ET Batterie LA Nettoyer Pour Transmission LA DE RefroidissementFig la Voir Lame LA Affiler Trapézoïdales CourroiesFrein DU Fonctionnement Fig la Voir Lame LA EnleverLames DES Entretien PneusLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant 13 .FIG UtilisationTonte DE Conseils Moteur LE Démarrer PourET Charrettes DES Remorquer Pour Accessoires Autres’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE Vérifier10 .FIG Arrière Marche EN FonctionnementTondeuse LA Utiliser Pour 12 .FIG 11 .FIGReculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentne -TIONSTA DE Frein LE Engager PourUtilisation Propriété la de lendommagement PA LA DE Tracteur LE Retirer Pour MontageCorrectement Sont Courroies LES Toutes SI Vérifier Toutes SI VérifierFig la Voir Batterie LA Vérifier DesmanCom des fonction la et mentceplalem Connaître pour mentnetionfonc tionsec laCarton LE Deballer DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerSiège Montar SIN PiezasCCA .MIN AMP/HR U1R DimensionSommaire Garantie’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

419055, 96042003402 specifications

The Poulan 96042003402 and 419055 are iconic chainsaw models that cater to both professional and amateur woodworkers. These powerful tools are engineered with innovative technologies and features that set them apart in the competitive landscaping and forestry market.

One of the standout characteristics of the Poulan 96042003402 is its robust engine, typically featuring a 40cc displacement. This engine provides powerful performance, enabling users to tackle a variety of cutting tasks efficiently. The engine is designed with advanced air injection systems that reduce air filter contamination, enhancing engine longevity and requiring less frequent maintenance. This feature not only translates to consistent performance but also makes the tool easier to operate over extended periods.

The 419055 model complements this with an enhanced ergonomic design. It includes padded handles that reduce vibration and improve comfort during prolonged use. This thoughtful design ensures that users can maintain control and reduce fatigue, which is particularly beneficial for those working on large projects or in challenging conditions.

Both models boast a quick-adjust chain tensioning system, simplifying the process of tightening the chain for optimal performance. This feature saves time and enhances safety, as proper chain tension is critical to effective cutting. Furthermore, these chainsaws are equipped with automatic oiler systems that ensure consistent lubrication, which not only enhances cutting efficiency but also extends chain life.

Poulan models are also known for their lightweight construction, improving maneuverability and ease of use. Weighing in under 15 pounds, these chainsaws are suitable for various users, from seasoned professionals to weekend warriors. Despite their lightweight design, they do not compromise power or performance, making them a versatile option for diverse tasks ranging from trimming branches to felling small trees.

Moreover, Poulan places a strong emphasis on user-friendly operation. These chainsaws are equipped with simple starting systems that minimize the effort needed to get the engine running, ensuring that users can quickly get to work. Safety features, including chain brakes and throttle locks, further enhance their usability, providing peace of mind during operation.

In conclusion, the Poulan 96042003402 and 419055 chainsaws are excellent choices for anyone looking for reliable, powerful, and user-friendly tools. With their combination of advanced technology, ergonomic design, and enhanced safety features, they stand out as trusted tools for a range of cutting tasks, meeting the needs of woodworkers and landscapers alike.
Top Page Image Contents