Poulan 419450 manual To Check Brake, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

 

INPUT PULLEY

CENTER SPAN

 

KEEPER

FIG. 22

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PO175H42LT ModelSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP NingLubrication Chart MaintenanceTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Clean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check BrakeTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when HOP Outdoor Products Customer Service DeptCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESDentretien Notes Dept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Correction Cause Problème Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage MoteurTracteur Carburateur LE Régler Pour Reglages ET Revision27 et 26 .Fig les Voir Batterie LA ReplacerRossage LA DE ENLEVEMENT/REMPLACEMENTAVANT/CAR Roues DES Convergence LA DE L’ALIGNEMENT Régler Pour’EN Courroie LA Remplacer Pour Fig la VoirTransmission DE Mentnetraî Freins LES Vérifier PourTondeuse DE Lame DE MENTNETRAÎD’EN Courroie Acer Rempl PourTondeuse DE Boîtier LE Niveler Pour 15 .FIGLautre À Côté DUN Réglage Moteur EntretienTransmission LA DE Refroidissement Sionmistrans LA DE Moteur FluideFig la Voir Lame LA Affiler Trapézoïdales CourroiesEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverGénérales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantTondre DE Conseils UtilisationTransmission LA Purger QuetiMoteur LE Démarrer DE Avant EN Fonctionnement DE Système Et 4 .Fig les VoirTracteur LE Transporter Pour Pentes LES Dans Utiliser PourTeurtrac Votre Utiliser Comment GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentnetionsta DE Frein LE Engager PourLSW02838 ’EMBRAYAGE Montage PA LA DE Tracteur LE Retirer Pour Tracteur Votre Monter Comment 1 .FIG Fig la Voir Siège LE InstallerDU Tracteur LE Sortir Pour Palette LAPente-Guide Montées NON PiécesSommaire Client DU ResponsabilitésProduit DE Spécifications Remorquage EntretienEnfants Général EntretienPEN LES Dans Fonctionnement TESGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsCom.poulan.www web site notre Visitez ModèleAUX Imprimé Avertissement
Top Page Image Contents