Poulan 188737 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

FIG. 28

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 30

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation PD18542STASafety Rules Safety Rules Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower Housing Belt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeTo Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points When operator leaves seat Tractor - Model Number PD1842ST PD18542STA SchematicElectrical KEY Part Description Chassis 5479J Plug BTN BlK Chassis and Enclosures170 Drive Steering Assembly Washer 25/32 x 1-5/8 x 16 Ga 188712 Seat 140551 Seat AssemblyWheels and Tires DecalsOptional Equipment EngineMower Lift 152 Mower DeckBracket Asm Deck 42 Sway Bar Service Notes Service Notes Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service
Top Page Image Contents