Poulan 191491 manual Install Mower and Drive Belt

Page 10

Retainer

Spring

Pin

Shoulder

Bolt Adjusting

Bar

Gauge

Wheel

3/8 Washer

3/8-16 Center

Locknut

 

INSTALL MOWER AND DRIVE BELT

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake.

1.Cut and remove ties securing anti- sway bar and belts. Swing anti-sway bar to left side of mower deck.

2.Slide mower under tractor with deflec-

tor shield to right side of tractor. IMPORTANT: Check belt for proper rout- ing in all mower pulley grooves.

3.If equipped, turn height adjustment knob counterclockwise until it stops.

4.Lower mower linkage with attachment lift control.

5.Be sure belt tension rod is in disen- gaged position.

6.Install belt into electric clutch pulley groove.

7.Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

8.Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

9.Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between

the plate assembly and mower brack- ets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: Check belt for proper rout- ing in all mower pulley grooves.

10. Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and en- gage slowly.

11.Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

Belt Tension Rod Disengaged Position

Chassis

Bracket

Gauge

Wheel

Double Loop

Retainer

Spring

USE PLIERS FOR

RETAINER SPRINGS

Loop Up

Lock Bracket

Electric Clutch

 

 

 

 

 

 

Pulley

Front

 

 

 

 

 

 

 

 

Suspension

Front Plate

 

 

Front

Brackets

Assembly

 

 

 

 

 

 

 

 

 

Mower

 

Double

 

 

Bracket

 

 

 

 

Loop Retainer

 

 

 

 

 

 

Springs

 

 

 

 

 

Single

 

 

 

Flanged

Loop

 

 

 

Retainer

 

 

 

Pin

 

 

 

Springs

 

 

 

 

Anti-Sway

Bar

Suspension Arms

 

Double Loop

 

Retainer Spring

 

(Outward pointing

Deflector Shield

deck pins)

10

 

Image 10
Contents Model NO. COGT22H48A Table of Contents WarrantyGeneral Operation Safety RulesII. Slope Operation III. Children IV. ServiceDo not Safety Rules Customer Responsibilities Product SpecificationsAPI-SF-SJ Unassembled Parts Gauge WheelsTo Remove Tractor from Carton ASSEMBLY/PRE-OPERATIONTools Required for Assembly Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck Install Mower and Drive Belt Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsBefore Starting the Engine To Start EnginePurge Transmission Mowing Tips General Recommendations Before Each USETires TractorBrake Operation Operator Presence SystemTransaxle Pump Fluid BatteryTransaxle Cooling BeltsAIR Filter CleaningIN-LINE Fuel Filter To Install Mower To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Drive Belt To Replace Mower Blade SEC- Ondary Drive BeltTo Check and Adjust Brake To Adjust Attachment ClutchTo Replace Motion Drive Belt Transmission Removal Replacement Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Replacing BatteryTo Adjust Throttle Control Cable To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation