Poulan 190781 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

•

Replace washers and snap retaining ring securely in

 

axle groove.

•

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

21

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO17542STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR ScreenBelts Transaxle CoolingAIR Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigReplacing Battery See Figs To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

190781 specifications

The Poulan 190781 is a versatile and powerful tool designed for both professional and home use, specifically catering to the needs of outdoor landscape maintenance and tree care. This chainsaw is engineered to deliver exceptional performance, ensuring that tasks like pruning, trimming, and cutting firewood are handled with ease and efficiency.

One of the standout features of the Poulan 190781 is its robust engine. Powered by a reliable 42cc engine, this chainsaw provides ample power for cutting through tough wood while maintaining efficient fuel consumption. The engine is engineered with advanced technologies that minimize emissions and reduce fuel consumption, making it an environmentally friendly choice for users who are conscious of their ecological footprint.

The chainsaw also features an 18-inch bar and chain, which strikes a perfect balance between maneuverability and cutting capacity. This length allows users to tackle a variety of cutting tasks, from small branches to larger logs, making it a multifaceted tool for homeowners and landscapers alike. The low kickback chain design enhances safety, as it reduces the risk of the chainsaw jumping back towards the user during operation.

In terms of user comfort, the Poulan 190781 comes equipped with an ergonomic handle that reduces fatigue during extended use. The anti-vibration system integrated into the design ensures a smoother experience, making it easier to handle for long periods without discomfort. Additionally, the tool comes with a simple and hassle-free starting system, which is particularly beneficial for those who may not be as technically inclined.

For maintenance and safety, the Poulan 190781 is designed with an easy-access air filter and chain tension adjustment, allowing users to keep the chainsaw in optimal condition with minimal effort. The chain brake feature provides added safety by allowing users to quickly stop the chain in the event of kickback.

Overall, the Poulan 190781 embodies a blend of power, efficiency, and comfort, making it an excellent choice for anyone looking to invest in a reliable chainsaw for their outdoor needs. Whether you're a seasoned professional or a beginner, this chainsaw offers the performance and features to meet your demands effectively.
Top Page Image Contents