Poulan 178493 owner manual To Attach Nose Roller See Fig, Install Mower and Drive Belt See Figs

Page 8

ASSEMBLY

TO ATTACH NOSE ROLLER (See Fig. 5)

Position brackets, 17/32 x 7/8 x 16 gauge washers, and nose roller between deck mounting brackets as shown. Be sure to position brackets on correct side, as shown.

Install hex bolts and lock nuts as shown. Tighten hardware securely.

NOTE: Be sure bracket tabs are positioned in tab holes in deck brackets.

TAB

“B”

HOLE

BRACKET

 

TAB

NOSE

 

ROLLER

 

HEX

BOLT

Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

• If equipped, turn height adjustment knob counterclock-

wise until it stops.

• Lower mower linkage with attachment lift control.

• Install belt into electric clutch pulley groove.

• Place the suspension arms on inward pointing deck

pins. Retain with double loop retainer spring with loops

down as shown.

• Install front plate assembly to tractor suspension brack-

ets and retain with single loop retainer springs as shown.

• Position front plate assembly between front mower

brackets. Raise deck and plate assembly to align holes

“A”

LOCK NUT

and insert flanged pins. Secure pins with double loop

retainer springs between the plate and mower brackets.

BRACKET

TAB

WASHER

FIG. 5

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake.

Cut and remove ties securing anti-sway bar and belts. Swing anti-sway bar to left side of mower deck.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

Raise deck to highest position.

Adjust gauge wheels before operating mower as shown in the Operation section of this manual.

 

DOUBLE LOOP

SUSPENSION ARMS

FRONT

ELECTRIC

CHASSIS

SUSPENSION

RETAINER SPRING

 

BRACKETS

CLUTCH

BRACKET

 

(Inward pointing deck pins)

FRONT

 

PULLEY

 

 

 

 

 

 

 

 

MOWER

 

FRONT

 

 

BRACKET

 

PLATE

 

 

 

 

ASSEMBLY

GAUGE

WHEEL

SINGLE LOOP

FLANGED PIN RETAINER SPRINGS

DOUBLE

LOOP

RETAINER ANTI-SWAY

SPRINGBAR

USE PLIERS FOR

RETAINER SPRINGS

LOOP

DOWN

DEFLECTOR

SHIELD

IDLER

PULLEY

FIG. 6

8

Image 8
Contents PRGT22H50C IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels and Brackets to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigsTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionLubrication Chart ¡ Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs Engine OIL FilterService and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigTo Replace Mower Drive Belt To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Attachment Clutch See FigTo Adjust Brake See Fig To Adjust Motion Control Lever See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentTo Remove Wheel for Repairs To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Hood and Grill Assembly See Fig To Adjust Attachment Lift Spring See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Other Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionOFF Service Notes Schematic Tractor - Model Number PRGT22H50CElectrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive KEY Part NO. NO. Description Steering Assembly Adapter, Wheel Steering Engine Spark Arrester KITKEY Part Description Seat Assembly Lift Assembly Mower Deck Washer, Hard Blade Mower Vented Decals Wheels & TiresService Notes Service Notes Service Notes Limited Warranty CUT OUT This Is a Tted SLOParts and Service