TROUBLESHOOTING POINTS
PROBLEM | CAUSE | CORRECTION | ||
Engine continues to run | 1. | Faulty | 1. | Check wiring, switches and connections. If not |
when operator leaves |
|
|
| corrected, contact an authorized service center/ |
seat with attachment |
|
|
| department. |
clutch engaged |
|
|
|
|
|
|
|
|
|
Poor cut - uneven | 1. | Worn, bent or loose blade. | 1. | Replace blade. Tighten blade bolt. |
| 2. | Mower deck not level. | 2. | Level mower deck. |
| 3. | Buildup of grass, leaves, and trash under mower. | 3. | Clean underside of mower housing. |
| 4. | Bent blade mandrel. | 4. | Replace blade mandrel. |
| 5. | Clogged mower deck vent holes from buildup of | 5. | Clean around mandrels to open vent holes. |
|
| grass, leaves, and trash around mandrels. |
|
|
|
|
|
|
|
Mower blades will not | 1. | Obstruction in clutch mechanism. | 1. | Remove obstruction. |
rotate | 2. | Worn/damaged mower drive belt. | 2. | Replace mower drive belt. |
| 3. | Frozen idler pulley. | 3. | Replace idler pulley. |
| 4. | Frozen blade mandrel. | 4. | Replace blade mandrel. |
|
|
|
|
|
Poor grass discharge | 1. | Engine speed too slow. | 1. | Place throttle control in “FAST” position. |
| 2. | Travel speed too fast. | 2. | Shift to slower speed. |
| 3. | Wet grass. | 3. | Allow grass to dry before mowing. |
| 4. | Mower deck not level. | 4. | Level mower deck. |
| 5. | Low/uneven tire air pressure. | 5. | Check tires for proper air pressure. |
| 6. | Worn, bent or loose blade. | 6. | Replace/sharpen blade. Tighten blade bolt. |
| 7. | Buildup of grass, leaves and trash under mower. | 7. | Clean underside of mower housing. |
| 8. | Mower drive belt worn. | 8. | Replace mower drive belt. |
| 9. | Blades improperly installed. | 9. | Reinstall blades sharp edge down. |
| 10. | Improper blades used. | 10. | Replace with blades listed in this manual. |
| 11. | Clogged mower deck vent holes from buildup of | 11. | Clean around mandrels to open vent holes. |
|
| grass, leaves, and trash around mandrels. |
|
|
|
|
|
|
|
Headlight(s) not working | 1. | Switch is “OFF”. | 1. | Turn switch “ON”. |
(if so equipped) | 2. | Bulb(s) or lamp(s) burned out. | 2. | Replace bulb(s) or lamp(s). |
| 3. | Faulty light switch. | 3. | Check/replace light switch. |
| 4. | Loose or damaged wiring. | 4. | Check wiring and connections. |
| 5. | Blown fuse. | 5. | Replace fuse. |
|
|
|
|
|
Battery will not charge | 1. | Bad battery cell(s). | 1. | Replace battery. |
| 2. | Poor cable connections. | 2. | Check/clean all connections. |
| 3. | Faulty regulator (if so equipped). | 3. | Replace regulator. |
| 4. | Faulty alternator. | 4. | Replace alternator. |
|
|
|
|
|
Loss of drive | 1. | Freewheel control in “disengaged” position. | 1. | Place freewheel control in “engaged” position. |
| 2. | Motion drive belt worn, damaged, or broken. | 2. | Replace motion drive belt. |
| 3. | Air trapped in transmission during shipment | 3. | Purge transmission. |
|
| or servicing. |
|
|
|
|
|
|
|
Engine “backfires” | 1. | Engine throttle control not set at “SLOW” | 1. | Move throttle control to “SLOW” position and allow |
when turning engine |
| position for 30 seconds before stopping engine. |
| to idle for 30 seconds before stopping engine. |
“OFF” |
|
|
|
|
|
|
|
|
|
28