Poulan PRGT22H50C To Remove Hood and Grill Assembly See Fig, To Replace Headlight Bulb

Page 25

SERVICE AND ADJUSTMENTS

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

	ADJUSTMENT	SPRING BUSHING
	BOLT	SPRING BUSHING
	BOLT

TERMINAL ACCESS DOOR

KEPS NUT

HEX BOLT

POSITIVE (RED)

CABLE

ATTACHMENT

LIFT SPRING

JAM NUT

TERMINAL GUARD

NEGATIVE (BLACK)

CABLE

FIG. 34

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 35)

FIG. 33

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO ADJUST ATTACHMENT LIFT SPRING (See Fig. 34)

•While holding spring bushing with wrench, loosen jam nut.

•Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments.

•Turn adjustment bolt counterclockwise for lighter at- tachments.

•Retighten jam nut against spring bushing.

IMPORTANT: DO NOT ADJUST FOR MAXIMUM SPRING TENSION WHEN USING LIGHT ATTACHMENTS SUCH AS A MOWER. ADJUST LIFT LEVER SPRING TO AID IN LIFTING ATTACHMENT. DO NOT OVERPOWER SPRING. WHEN REMOVING ATTACHMENT, ALWAYS ADJUST SPRING TENSION TO ITS LOWEST POSITION.

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedures.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 35

25

Image 25

Contents PRGT22H50C Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels and Brackets to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsCustomer Responsibilities Lubrication Chart ¡General Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Replace Mower Drive BeltTo Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Motion Control Lever See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs To Adjust Attachment Lift Spring See Fig To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Fuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor - Model Number PRGT22H50C SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive KEY Part NO. NO. Description Steering Assembly Adapter, Wheel Steering Spark Arrester KIT EngineKEY Part Description Seat Assembly Lift Assembly Mower Deck Washer, Hard Blade Mower Vented Wheels & Tires DecalsService Notes Service Notes Service Notes Limited Warranty This Tted Lines SLO CUTParts and Service