Poulan PP3516AVX Tools required, To Sharpen Chain, Carburetor Adjustment, Right, Wrong

Page 17

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

Conditions which indicate the need for chain sharpening:

SReduction in size of wood chips. The size of the wood chip will decrease as the chain gets duller until it becomes more like a powder than a chip. Note that dead or

rotted wood will not produce a good chip.

SSaw cuts to one side or at an angle. S Saw has to be forced through the cut.

Tools required:

S5/32 inch (4 mm) diameter round file and

file holder

SFlat file

SDepth gauge tool

TO SHARPEN CHAIN:

1.Move ON/STOP switch to the STOP position.

2.Check chain for proper tension. Adjust chain tension if necessary. See CHAIN TENSION section.

3.Sharpen cutters.

S To sharpen the cutters, position the file holder level (90˚) so that it rests on the top edges of the cutter and depth gauge.

NOTE: The chain has both left and right hand cutters.

File Holder

File

SFile chain to meet the specifications as shown.

 

85˚

60

30˚

 

 

Hook Angle

 

0.025 inch

 

 

 

 

(0.65 mm)

 

 

Rounded

Right

Corner

 

Too Much Hook Angle

 

Squared Off

 

 

Corner

Wrong

 

WARNING:

Maintain the proper

hook angle according to the manufacturer’s specifications for the chain you are using. Im- proper hook angle will increase the chance of kickback which can result in serious injury.

4. Check and lower depth gauges.

Cutter

90˚

Depth Gauge Tool

File

Depth Gauge

SAlign the 30˚ file holder marks paral- lel with the bar and to the center of the chain.

Cutter

30˚

Cutter

File Holder Line

 

SSharpen cutters on one side of the chain first. File from the inside of each cutter to the outside. Then, turn the chain saw around and repeat the pro-

cess for the other side of the chain.

SFile on the forward stroke only. Use 2

or 3 strokes per cutting edge.

SKeep all cutters the same length when filing.

SFile enough to remove any damage to cutting edges (side plate and top plate of cutter).

All Cutters

Remove Damage

Same Length

 

 

Top Plate

 

Side Plate

Depth Gauge

SPlace gauge tool on cutter.

SIf the depth gauge is higher than the depth gauge tool, file it level to the top of the depth gauge tool.

SMaintain rounded front corner of depth gauge with a flat file.

NOTE: The very top of the depth gauge should be flat with the front

half rounded off with a flat file.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

CARBURETOR ADJUSTMENT

WARNING: The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Always use two hands when operating the chain saw Using the chain sawStarting Reminder Chain TensioningOperate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance of Kickback KickbackMaintain Control Avoid Pinch-KickbackChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Front Hand Guard, designed to reduceLoosen AssemblyAttaching the BAR & Chain If Cutters Adjusting the tensionKnow Your Chain SAW OperationTighten ON/STOPThrottle Trigger ON/STOP Switch Chain BrakeThrottle LOCK-OUT Chain TensionImportant Points to Remember BAR and Chain LubricationDifficult Starting or starting a flooded engine Starting a Warm EngineBraking function control Caution The chain brake must be Inertia activating function controlNotch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Cutting a Fallen Tree Bucking Using a LOG or Support StandImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points ServiceLimbing PruningGeneral Recommendations Inspect and Clean Unit and DecalsCheck for Damaged or Worn Parts Check for Loose Fasteners and PartsCleaning the Spark ARREST- ING Screen Clean AIR FilterChain Adjustment Check Chain BrakeTools required Carburetor AdjustmentTo Sharpen Chain RightStorage Empty fuel tank and refill with Load Adjustment EngineLigations The U.S. Environmental Poulan PRONANCE, Replacement and Repair of Emission Related Parts Any

PP3516AVX specifications

The Poulan PP3516AVX is a powerful and efficient chainsaw designed to cater to both novice and experienced users. Known for its versatile features and robust design, this chainsaw is ideal for a range of tasks, from light pruning to heavy-duty cutting, making it a reliable tool for homeowners and professionals alike.

One of the standout features of the Poulan PP3516AVX is its 35cc two-cycle engine. This engine delivers ample power, enabling users to tackle a variety of jobs with ease. The lightweight design, combined with an ergonomic handle, ensures that users can operate the chainsaw comfortably for extended periods without experiencing fatigue. The chainsaw’s 16-inch bar and chain strike a perfect balance between reach and control, making it suitable for cutting through branches, logs, and other materials effectively.

The technology integrated into the Poulan PP3516AVX enhances its performance and user experience. The chainsaw is equipped with the OxyPower engine, which provides more power while reducing emissions. This eco-friendly feature is not only better for the environment but also improves fuel efficiency, allowing users to work longer between refueling. Additionally, the air filtration system keeps the engine clean, prolonging its life and reducing maintenance needs.

The tool-less chain tensioning system is another significant advantage of the PP3516AVX. This feature allows users to adjust the chain tension easily, ensuring optimal performance and safety without needing extra tools. The easy-access fuel and oil caps simplify the refueling process, minimizing downtime during work sessions.

Safety is a critical aspect of any chainsaw, and the Poulan PP3516AVX is designed with this in mind. It includes a chain brake that stops the chain immediately in case of kickback, providing added protection for users. The integrated hand guard also shields the hands from debris, enhancing safety while operating the chainsaw.

In summary, the Poulan PP3516AVX is a versatile and user-friendly chainsaw, perfect for a variety of cutting tasks. With its powerful engine, innovative technologies, and safety features, it stands out as a reliable choice for anyone looking to take on outdoor projects with confidence. Whether for light maintenance or larger scale jobs, the PP3516AVX delivers performance and convenience in one efficient package.
Top Page Image Contents