Poulan PP3516, PP4018 Cutting a Fallen Tree, Important Points, Types of Cutting Used for Bucking

Page 12

Hinge holds tree on stump and helps control fall

Opening

of felling cut

Closing of notch

NOTE: Before felling cut is complete, use wedges to open the cut if necessary to control the direction of fall. To avoid kickback and chain damage, use wood or plastic wedges, but never steel or iron wedges.

SBe alert to signs that the tree is ready to

fall: cracking sounds, widening of the fell- ing cut, or movement in the upper branches.

SAs tree starts to fall, stop saw, put it down,

and get away quickly on your planned re- treat path.

SDO NOT cut down a partially fallen tree with your saw. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn’t fall com- pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log size.

WARNING: Do not stand on the log being cut. Any portion can roll causing loss of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

SCut only one log at a time.

S Cut shattered wood very carefully; sharp pieces of wood could be flung toward opera- tor.

SUse a sawhorse to cut small logs. Never allow another person to hold the log while

cutting and never hold the log with your leg or foot.

SDo not cut in an area where logs, limbs, and roots are tangled such as in a blown down area. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

WARNING: If saw becomes pinched or hung in a log, don’t try to force it out. You can lose control of the saw resulting in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the cut until the saw can be removed easily. Restart the saw and carefully reenter the cut. To avoid kickback and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the bottom of the saw against the log. When overcutting use light downward pres- sure.

Overcutting

Undercutting

Undercutting involves cutting on the under- side of the log with top of saw against the log. When undercutting use light upward pres- sure. Hold saw firmly and maintain control. The saw will tend to push back toward you.

WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position.

Always make your first cut on the compres- sion side of the log. The compression side of the log is where the pressure of the log’s weight is concentrated.

First cut on compression side of log

Second cut

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

SOvercut through 1/3 of the diameter of the

log.

SRoll the log over and finish with a second

overcut.

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustrations for cutting logs with a compres- sion side.

BUCKING USING A LOG OR

SUPPORT STAND

SRemember your first cut is always on the

compression side of the log.

(Refer to the illustrations below for your first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

12

Image 12
Contents English Español FrançaisElectrolux Home Products, Inc 545001498Identification of Symbols Safety RulesStarting Reminder Plan AheadOperate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notBAR ModelAdjusting the tension Chain TensionChecking the tension Operation Before Starting Engine Fueling Engine BAR and Chain LubricationImportant Points to Remember Ignition Switch Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Using a LOG or Support Stand Cutting a Fallen TreeImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning Service Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Troubleshooting Table Cause Remedy EngineOther Limited Warranty Your Warranty Rights and ObligaTions The U.S. Environmental Protection Electrolux Home PRODUCTS, INCPlacement and Repair of Emission Sion Control Warranty Parts ListConsequential Damages Electro