Poulan BH 2660 instruction manual Need ASSISTANCE?

Page 15

authorized

service

dealer

or

call

1--800--554--6723.

 

 

 

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

SBurring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and dis- card.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0.6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

 

Plug

 

STORAGE

 

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit. Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an open flame from hot water heaters, electric

motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

NEED ASSISTANCE?

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your authorized service dealer.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents English Français Manual de Instrucciones Manuel d’InstructionsPlan Ahead Identification of SymbolsSafety Rules Starting ReminderKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionElbow locked Clear The Working Area Maintain ControlReduce the Chance of Kickback Do not cut more than one log at a timeGuide bar up and back toward the operator Kickback Safety FeaturesChain Brake and CKA Angle Chain saws as set by Ansi B175.1Assembly Inside view Chain Brake Adjustment located on Chain BrakeComputed kickback angle CKA Table Checking the tension Adjusting the tensionThrottle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationCutting Methods Starting a Warm EngineImportant Points Carefully plan your sawing operation in ad- vance Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing ServicePruning Limbing and Pruning Important PointsInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen Carburetor AdjustmentNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Tions The U.S. Environmental ProtectionIntermediate 125 hours Extended 300 hours

BH 2660 specifications

The Poulan BH 2660 is a versatile and efficient piece of equipment designed for homeowners and professional landscapers alike. Known for its power and durability, this blower and vacuum combination is perfect for various yard work tasks, ensuring your outdoor space remains pristine throughout the seasons.

One of the standout features of the Poulan BH 2660 is its impressive 26 cc, 2-cycle engine. This engine provides ample power for tackling tough debris and leaves, allowing users to complete their tasks quickly and efficiently. Its lightweight design enhances maneuverability, making it easy to navigate around trees, flower beds, and other obstacles in your yard.

The Poulan BH 2660 boasts a dual-function capability, allowing it to not only blow leaves and debris but also vacuum them up. The transition between these two modes is seamless, enabling users to switch their approach based on specific yard needs. The vacuum mode features a mulching capability, breaking down leaves into fine pieces that can be easily composted or disposed of, making yard cleanup more environmentally friendly.

A key characteristic of the Poulan BH 2660 is its ergonomic design. The blower is equipped with a comfortable handle and a well-balanced structure, reducing fatigue during extended use. The shoulder strap helps distribute weight evenly, allowing for a more user-friendly experience. Another notable technology in this model is its easy-start system, which minimizes starting effort and ensures hassle-free ignition.

The blower also features an adjustable nozzle, allowing users to modify the airflow direction and intensity. This feature is particularly useful for tackling specific areas or adapting to different types of debris, whether they are light leaves or heavier twigs.

In terms of maintenance, Poulan has designed the BH 2660 with accessibility in mind. Regular upkeep is simplified, ensuring the blower remains in top condition for longer. Additionally, the fuel-efficient engine minimizes emissions, making it a more eco-conscious choice for yard care.

Overall, the Poulan BH 2660 combines power, efficiency, and ease of use in a reliable package, making it an excellent choice for anyone seeking to maintain their outdoor spaces effectively. With its range of features and user-friendly design, it's no wonder that this model has garnered attention among homeowners and professionals alike. Whether you are facing a tough autumn clean-up or general yard maintenance, the Poulan BH 2660 is equipped to meet all your landscaping needs.
Top Page Image Contents