Poulan 966063101 instruction manual Important Points to Remember, Starting a Warm Engine

Page 10

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle If your hand slips off the front handlebarAssembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Primer Bulb Throttle LOCK-OUTCHOKE/FAST Idle Lever Chain BrakeDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Check Guide BAR Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelReplace Spark Plug Cleaning the Spark ARREST- ING ScreenChain Adjustment To Sharpen ChainCooling System Carburetor AdjustmentIdle Speed-T RightFuel System StorageSeasonal Storage EngineLoad Adjustment Engine Empty fuel tank and refill withPoulan PRO Ligations The U.S. Environmental

966063101 specifications

The Poulan 966063101 is a versatile and robust chainsaw designed to meet the demands of both professional tree care specialists and avid home gardeners. Known for its durability and powerful performance, this chainsaw stands out in the competitive market of outdoor power equipment.

One of the key features of the Poulan 966063101 is its powerful engine. Equipped with a potent 50cc two-stroke engine, it provides sufficient power to tackle a variety of cutting tasks, from simple limb trimming to taking down larger trees. The engine's design emphasizes efficiency, delivering optimal performance without excessive fuel consumption. This is especially beneficial for users who engage in extended cutting sessions, allowing for longer operational times without the need for frequent refueling.

The chainsaw features a 20-inch cutting bar and chain, which is ideal for medium to large cutting applications. This length allows the user to make precise cuts while handling thicker branches and logs effectively. The robust chain design ensures smooth cuts and minimizes kickback, enhancing safety during operation.

Another standout characteristic of the Poulan 966063101 is its ease of use. It features an automatic oiler that supplies the chain with oil during operation, ensuring proper lubrication and maintaining the integrity of the chain. Additionally, the chainsaw has a tool-less chain tensioning system, allowing users to quickly and easily adjust the chain tension without the need for additional tools, promoting efficiency and convenience.

The ergonomically designed handle provides excellent grip and control, reducing operator fatigue during longer use. Vibration dampening technology further enhances comfort, keeping the operator’s hands steady and reducing strain even after prolonged usage.

Safety is a crucial aspect of any chainsaw, and the Poulan 966063101 does not disappoint. It comes equipped with a chain brake that quickly stops the chain in case of kickback, protecting the user from accidents.

In conclusion, the Poulan 966063101 combines power, efficiency, and safety features to provide an exceptional chainsaw experience. With its reliable performance, user-friendly design, and advanced technologies, it is an excellent choice for anyone in need of a dependable tool for their cutting tasks. Whether for home use or professional landscaping, the Poulan 966063101 is built to deliver.
Top Page Image Contents