Poulan 545047544 Before Starting Engine Fueling Engine, BAR and Chain Lubrication

Page 9

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gaso- line. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/Weed Eater brand syn- thetic oil. Pour the entire contents of this con- tainer into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PROR bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PROR oil resists high temperature thinning.

If Poulan or Poulan PROR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or meth- anol) can attract moisture which leads to sepa-

ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine prob- lems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15-- 18(40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

9

Image 9
Contents 12/8/05 SM4218 AV For Occasional Use OnlyAlways use two hands when operating the chain saw Using the chain sawStarting Reminder Plan AheadMaintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlKickback Safety Features Chain Brake and CKA AngleIf your hand slips off the front handlebar Assembly Adjusting Screw Tensioning RackAttaching the BAR & Chain If not Adjusting the tension Chain TensionChecking the tension Operation BAR and Chain Lubrication Before Starting Engine Fueling EngineImportant Points to Remember Cation Always stop the engine before removing the oil capDifficult Starting or starting a flooded engine Starting a Warm EngineBraking function control Caution The chain brake must be Inertia activating function controlTree Felling Techniques Operating TipsFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Bucking Using a LOG or Support StandImportant Points Types of Cutting Used for BuckingLimbing and Pruning Important Points LimbingPruning Service Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Empty fuel tank and refill withTions The U.S. Environmental Protection Limited WarrantyConsequential Damages Electro