Poulan 530088308 instruction manual Storage, Troubleshooting Table Cause Remedy

Page 15

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch socket wrench. Spark plug gap should be 0.025 inches.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

 

 

 

Cylinder

Spark

 

 

 

 

 

 

 

 

 

 

Cover

 

 

 

 

 

 

 

 

 

 

 

 

Plug Boot

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spark

 

 

 

 

 

Plug

 

 

 

 

 

STORAGE

 

 

 

 

 

WARNING: Stop engine and allow to cool, and secure the unit before storing or transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach

sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children.

SBefore storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

SClean the unit before storing. Pay particu- lar attention to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean the plastic surfaces.

SDo not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc.

SStore in a dry area out of the reach of chil- dren.

CAUTION: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or fuel tank during storage. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to fuel mixture separation and formation of acids during storage. Acidic gas can damage the engine.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

TROUBLE

CAUSE

REMEDY

 

 

 

 

Engine will not

1. Ignition switch off.

1.

Move ignition switch to ON.

start or will run

2. Engine flooded.

2.

See “Difficult Starting” in

only a few

 

 

 

Operation Section.

seconds after

3. Fuel tank empty.

3.

Fill tank with correct fuel mixture.

starting.

3. Spark plug not firing.

4.

Install new spark plug.

 

4. Fuel not reaching

5.

Check for dirty fuel filter; replace.

 

 

carburetor.

 

Check for kinked or split fuel line;

 

 

 

 

repair or replace.

 

 

 

 

Engine will

1.

Carburetor requires

1. Contact an authorized service dealer.

not idle

 

adjustment

 

 

properly.

2.

Crankshaft seals worn.

2. Contact an authorized service dealer.

 

 

 

 

Engine will not

1.

Air filter dirty.

1. Clean or replace air filter.

accelerate,

2.

Spark plug fouled.

2. Clean or replace plug and regap.

lacks power,

3.

Chain brake engaged.

3. Disengage chain brake.

or dies under

4.

Carburetor requires

4. Contact an authorized service dealer.

a load.

 

adjustment.

 

 

 

 

 

 

Engine

1. Too much oil mixed with

1.

Empty fuel tank and refill with

smokes

 

gasoline.

 

correct fuel mixture.

excessively.

 

 

 

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Mississauga, Ontario L5R 4C2 Manual de Instrucciones Manuel d’InstructionsHearing Afety Hat Protection Eye Snug Fitting Plan AheadKickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Obstructions Clear The Working Area Kickback Safety FeaturesReduce the Chance Kickback Maintain ControlChain Brake and CKA Angle Attaching the BAR & Chain If not Adjusting the tension Checking the tensionChain Tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember ON/STOP SwitchFueling Engine BAR and Chain LubricationImportant Points Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlPlan a clear retreat path Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Essary wear can occur to the chain, bar, and engineBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing Cleaning the air filterPruning Limbing and Pruning Important PointsInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenCarburetor Adjustments BAR MaintenanceTroubleshooting Table Cause Remedy StorageStore in a dry area out of the reach of chil- dren Need Service PART? Ered Repair or ReplacementNeed ASSISTANCE? Warranty Parts List Carburetor, Igni

530088308 specifications

The Poulan 530088308 is a high-quality replacement chain designed to deliver exceptional performance for chainsaw enthusiasts and professionals alike. This chainsaw chain is engineered for reliability and durability, ensuring users can tackle various cutting tasks with ease and efficiency.

One of the standout features of the Poulan 530088308 is its compatibility with a wide range of chainsaw models. This versatility makes it an ideal choice for those who own multiple saw brands. The chain is designed with a pitch of 3/8 inches and a gauge of .050 inches, which provides a perfect balance of cutting power and precision. The chain length typically includes 50 links, making it suitable for many chainsaws that require similar specifications.

The technology behind the Poulan 530088308 includes high-performance materials that enhance cutting speed and efficiency. The chain is crafted from high-quality steel, which not only contributes to its longevity but also helps maintain sharpness even after numerous uses. The precision-ground teeth of the chain ensure smooth and consistent cutting action, allowing users to produce clean cuts in various wood types, including hardwoods and softwoods.

Another critical characteristic of this chainsaw chain is its ease of installation and maintenance. The design facilitates quick and straightforward replacement, enabling users to get back to work in no time. Additionally, the Poulan 530088308 is engineered for optimal lubrication, which decreases wear and tear, prolonging the life of both the chain and the chainsaw itself.

The safety features incorporated into the design of the Poulan 530088308 cannot be overlooked. The chain is designed to reduce kickback, ensuring a safer cutting experience. For those who prioritize safety while operating their chainsaws, this aspect is critical in preventing accidents and injuries.

In conclusion, the Poulan 530088308 chainsaw chain stands out due to its compatibility, high-quality materials, precision engineering, and user-friendly design. Whether you are a professional woodworker or a home maintenance enthusiast, investing in this replacement chain can enhance your cutting efficiency and provide a reliable solution for your chainsaw needs.
Top Page Image Contents